Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012TGN
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL; 2018 MY Camry [03/2017 - 06/2017]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here 2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • If an airbag deploys for any reason, it may cause a serious injury.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE FRONT DOOR SCUFF PLATE

Click here 2018 MY Camry [03/2017 - 06/2017]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the front door opening trim weatherstrip.

5. REMOVE REAR DOOR SCUFF PLATE

Click here 2018 MY Camry [03/2017 - 06/2017]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the rear door opening trim weatherstrip.

7. REMOVE LAP BELT OUTER ANCHOR COVER

(a) Disengage the 3 claws to remove the lap belt outer anchor cover.

8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.

9. REMOVE LOWER CENTER PILLAR GARNISH

Click here 2018 MY Camry [03/2017 - 06/2017]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

10. REMOVE UPPER CENTER PILLAR GARNISH

Click here 2018 MY Camry [03/2017 - 06/2017]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

11. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

(b) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.

*a

Protective Tape

*b

Locking Button

*c

Release

(c) Remove the 2 bolts.

(d) Disengage the 2 guides to remove the front seat outer belt assembly.

12. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.