| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012TE3 |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - ] |
| Title: PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: C1622; Back Camera Disconnected; 2018 - 2024 MY Camry [03/2017 - ] | ||
|
DTC |
C1622 |
Back Camera Disconnected |
DESCRIPTION
This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the rear television camera assembly, and the radio and display receiver assembly are not normal as a result of its self check.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1622 |
Back Camera Disconnected |
Open or short in the rear television camera assembly signal circuit |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click here
![2018 MY Camry [03/2017 - 06/2017]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
(a) Disconnect the K2 radio and display receiver assembly connector.
(b) Disconnect the m1 rear television camera assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K2-28 (V+) - m1-3 (CV+) |
Always |
Below 1 Ω |
|
K2-29 (V-) - m1-2 (CV-) |
Always |
Below 1 Ω |
|
K2-27 (CGND) - m1-5 (CGND) |
Always |
Below 1 Ω |
|
K2-28 (V+) or m1-3 (CV+) - Body ground |
Always |
10 kΩ or higher |
|
K2-29 (V-) or m1-2 (CV-) - Body ground |
Always |
10 kΩ or higher |
|
K2-27 (CGND) or m1-5 (CGND) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - GROUND) |
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
m1-6 (CB+) - Body ground |
Engine switch on (ACC) |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V-, CGND) |
(a) Reconnect the K2 radio and display receiver assembly connector.
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
|
4. |
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V+, GND1) |
(a) Reconnect the m1 rear television camera assembly connector.
(b) Using an oscilloscope, check the waveform of the rear television camera assembly.
|
*a |
Component with harness connected (Radio and Display Receiver Assembly) |
HINT:
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
OK:
Waveform is similar to that shown in the illustration.
|
Item |
Content |
|
Measurement terminal |
K2-28 (V+) - K3-1 (GND1) |
|
Measurement setting |
200 mV/DIV., 50 μs./DIV. |
|
Condition |
Engine switch on (IG), shift lever in R |
HINT:
- The video waveform changes according to the image sent by the rear television camera assembly.
- The video waveform is constantly output when the engine switch is on (ACC).
|
*a |
Waveform 1 (camera lens is not covered, displaying an image) |
|
*b |
Waveform 2 (camera lens is covered, blacking out the screen) |
|
*c |
Synchronization Signal |
|
*d |
Video Waveform |
| OK |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG |
|
REPLACE REAR TELEVISION CAMERA ASSEMBLY
|
|
|