Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000012T40 |
Model Year Start: 2018 |
Model: Camry |
Prod Date Range: [03/2017 - 06/2017] |
Title: NETWORKING: CAN COMMUNICATION SYSTEM: Open in Bus 2 Main Bus Line; 2018 MY Camry [03/2017 - 06/2017] |
Open in Bus 2 Main Bus Line
|
DESCRIPTION
There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
Symptom
|
Trouble Area
|
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
|
-
CAN main bus lines or connector
-
Central gateway ECU (network gateway ECU)
-
ECM
-
No. 2 CAN junction connector
-
No. 4 CAN junction connector
|
This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
-
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
-
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
1.
|
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
|
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A67 No. 2 CAN junction connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to No. 2 CAN Junction Connector)
|
*b
|
to No. 4 CAN Junction Connector
|
*c
|
to ECM
|
-
|
-
|
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Connected to
|
A67-10 (CANH) - A67-21 (CANL)
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
No. 4 CAN junction connector
|
A67-11 (CANH) - A67-22 (CANL)
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
ECM
|
Result
|
Proceed to
|
OK
|
A
|
NG (Line to ECM)
|
B
|
NG (Line to No. 4 CAN junction connector)
|
C
|
A |
|
REPLACE NO. 2 CAN JUNCTION CONNECTOR
|
B
|
|
|
2.
|
CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM - NO. 2 CAN JUNCTION CONNECTOR)
|
(a) Reconnect the A67 No. 2 CAN junction connector.
(b) Disconnect the A24 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A24-8 (CANH) - A24-18 (CANL)
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
|
|
*a
|
Front view of wire harness connector
(to ECM)
|
|
|
NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - NO. 2 CAN JUNCTION CONNECTOR)
|
3.
|
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
|
(a) Reconnect the A67 No. 2 CAN junction connector.
(b) Disconnect the K128 No. 4 CAN junction connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to No. 4 CAN Junction Connector)
|
*b
|
to No. 2 CAN Junction Connector
|
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Connected to
|
K128-11 (CANH) - K128-22 (CANL)
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
No. 2 CAN junction connector
|
NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
|
OK
|
|
|
4.
|
CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
|
(a) Reconnect the K128 No. 4 CAN junction connector.
(b) Disconnect the K127 No. 4 CAN junction connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to No. 4 CAN Junction Connector)
|
*b
|
to Central Gateway ECU (Network Gateway ECU)
|
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Connected to
|
K127-1 (CANH) - K127-12 (CANL)
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
Central gateway ECU (network gateway ECU)
|
OK |
|
REPLACE NO. 4 CAN JUNCTION CONNECTOR
|
NG
|
|
|
5.
|
CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 CAN JUNCTION CONNECTOR)
|
(a) Reconnect the K127 No. 4 CAN junction connector.
(b) Disconnect the K76 central gateway ECU (network gateway ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
K76-18 (CA4H) - K76-17 (CA4L)
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
|
|
*a
|
Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
|
|
|
NG |
|
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 CAN JUNCTION CONNECTOR)
|
|