-
Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the Techstream.
Click here
![2018 MY Camry [03/2017 - 06/2017]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE](/t3Portal/stylegraphics/info.gif)
-
Communication stop history for "Main Body" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Main Body" is 6 or more.)
Click here
-
Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output.
Click here
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012T3J |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - ] |
| Title: NETWORKING: CAN COMMUNICATION SYSTEM: Main Body ECU Communication Stop Mode; 2018 - 2024 MY Camry [03/2017 - ] | ||
|
Main Body ECU Communication Stop Mode |
DESCRIPTION
|
Detection Item |
Symptom |
Trouble Area |
|---|---|---|
|
Main Body ECU Communication Stop Mode |
Any of the following conditions are met: |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
-
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
- Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
-
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
-
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
-
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
-
w/ Smart Key System
Click here
-
w/o Smart Key System
Click here
-
w/ Smart Key System
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
|
1. |
CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K52 main body ECU (multiplex network body ECU) connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG |
|
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
|
|
2. |
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) |
(a) Remove the main body ECU (multiplex network body ECU).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
NOTICE: Perform this inspection with the wire harness connected to the instrument panel junction block assembly. |
|
(c) Reconnect the cable to the negative (-) battery terminal.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
MB-30 (ACC) - Body ground |
Ignition switch ACC |
11 to 14 V |
|
MB-31 (BECU) - Body ground |
Always |
11 to 14 V |
|
MB-32 (IG) - Body ground |
Ignition switch ON |
11 to 14 V |
NOTICE:
Perform this inspection with the wire harness connected to the instrument panel junction block assembly.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (BECU) |
B |
|
NG (ACC) |
C |
|
NG (IG) |
D |
|
NG (GND1) |
E |
| A |
|
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
|
| C |
|
| D |
|
| E |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the 3C instrument panel junction block assembly connector.
(c) Reconnect the cable to the negative (-) battery terminal.
|
(d) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK |
|
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (BECU SIGNAL CIRCUIT) |
|
4. |
CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the 3B instrument panel junction block assembly connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK |
|
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT) |
|
|