| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012SQB |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 06/2017] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CURTAIN SHIELD AIRBAG ASSEMBLY: REMOVAL; 2018 MY Camry [03/2017 - 06/2017] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during curtain shield airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. REMOVE ROOF HEADLINING ASSEMBLY
Click here
3. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
CAUTION:
When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side |
NOTICE:
When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.
(a) Check that the ignition switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button and disconnect the airbag connector.
|
*a |
Airbag Connector |
|
*b |
Airbag Connector Locking Button |
|
*c |
Protective Tape |
|
Release in this Direction |
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(d) Using a needle nose pliers No. 2 or equivalent, remove the 3 pins from the 2 clips (A) and clip (B).
NOTICE:
Do not damage the pins.
|
*1 |
Pin |
- |
- |
|
*a |
Clip (A) |
*b |
Clip (B) |
|
*c |
Clip (C) |
*d |
Clip (D) |
|
*e |
Needle Nose Pliers No. 2 |
*f |
Thin Screwdriver |
|
|
Remove in this Direction |
- |
- |
(e) Using 2 thin screwdrivers, disengage the 2 claws of each clip (A) and (B), and separate the 2 clips (A) and clip (B) from the vehicle body as shown in the illustration.
HINT:
Separate the 2 clips (A), clip (B) and curtain shield airbag assembly from the vehicle body as a unit.
(f) Disengage the 4 clips (C) and remove the clip (D).
(g) While holding the curtain shield airbag assembly, remove the 5 bolts and curtain shield airbag assembly.
(h) Remove the 2 clips (A) and clip (B) from the curtain shield airbag assembly.
|
|