Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012SON
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1660; P Seat Airbag Active Mode Indicator; 2018 - 2024 MY Camry [03/2017 -        ]

DTC

B1660

P Seat Airbag Active Mode Indicator

DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator (telltale light assembly).

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag assembly and lower No. 2 instrument panel airbag assembly.

DTC B1660 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1660

P Seat Airbag Active Mode Indicator

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit.
  • Passenger airbag ON/OFF indicator malfunction
  • Airbag sensor assembly malfunction
  • Instrument panel wire
  • Instrument panel junction block assembly
  • Passenger airbag ON/OFF indicator (Telltale light assembly)
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.

CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

(a) Turn the ignition switch to ON.

(b) Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click here 2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: OPERATION CHECK 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: OPERATION CHECK 2020 MY Camry [09/2019 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: OPERATION CHECK 2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: OPERATION CHECK 2023 - 2024 MY Camry [08/2022 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: OPERATION CHECK

Result

Proceed to

ON/OFF indicator illumination is always on.

A

ON/OFF indicator illumination is always off.

B

B

GO TO STEP 8

A

2.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

3.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE INSTRUMENT PANEL WIRE

OK

4.

CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

(a) Connect the connector to the telltale light assembly and instrument panel junction block assembly.

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON.

(d) Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.

NG

GO TO STEP 6

OK

5.

CHECK DTC

(a) Turn the ignition switch off.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Connect the connector to the airbag sensor assembly.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the ignition switch to ON, and wait for at least 60 seconds.

(f) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(g) Turn the ignition switch off.

(h) Turn the ignition switch to ON, and wait for at least 60 seconds.

(i) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

OK:

DTC B1660 is not output.

HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.

OK

USE SIMULATION METHOD TO CHECK 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

NG

REPLACE AIRBAG SENSOR ASSEMBLY 2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

6.

CHECK WIRE HARNESS

(a) Turn the ignition switch off.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

*4

Instrument Panel Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Telltale Light Assembly)

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the connector from the telltale light assembly.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the ignition switch to ON.

(f) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K36-5 (PAON) - Body ground

Ignition switch ON

Below 1 V

K36-4 (P-AB) - Body ground

Ignition switch ON

Below 1 V

(g) Turn the ignition switch off.

(h) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(i) Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K36-5 (PAON) - K36-4 (P-AB)

Always

Below 1 Ω

(k) Disconnect the service wire from connector B.

(l) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K36-5 (PAON) - K36-4 (P-AB)

Always

1 MΩ or higher

K36-5 (PAON) - Body ground

Always

1 MΩ or higher

K36-4 (P-AB) - Body ground

Always

1 MΩ or higher

OK

REPLACE TELLTALE LIGHT ASSEMBLY 2018 - 2020 MY Camry [03/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: TELLTALE LIGHT ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: TELLTALE LIGHT ASSEMBLY: REMOVAL

NG

7.

CHECK INSTRUMENT PANEL WIRE

(a) Disconnect the connector from the instrument panel junction block assembly.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

*4

Instrument Panel Wire

*5

Service Wire

-

-

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

*c

Front view of wire harness connector

(to Telltale Light Assembly)

-

-

(b) Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-8 (PAON) - 3A-46 (P-AB)

Always

Below 1 Ω

(d) Disconnect the service wire from connector B.

(e) Using a service wire, connect terminals 5 (PAON) and 4 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(f) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-29 (PAON) - 3A-51 (P-AB)

Always

Below 1 Ω

(g) Disconnect the service wire from connector E.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-8 (PAON) - Body ground or other terminals

Always

1 MΩ or higher

3A-29 (PAON) - Body ground or other terminals

Always

1 MΩ or higher

3A-46 (P-AB) - Body ground or other terminals

Always

1 MΩ or higher

3A-51 (P-AB) - Body ground or other terminals

Always

1 MΩ or higher

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

8.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

9.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE INSTRUMENT PANEL WIRE

OK

10.

CHECK WIRE HARNESS

(a) Connect the connector to the instrument panel junction block assembly.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

*4

Instrument Panel Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Telltale Light Assembly)

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K36-5 (PAON) - Body ground

Ignition switch ON

Below 1 V

K36-4 (P-AB) - Body ground

Ignition switch ON

Below 1 V

(e) Turn the ignition switch off.

(f) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K36-5 (PAON) - K36-4 (P-AB)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K36-5 (PAON) - K36-4 (P-AB)

Always

1 MΩ or higher

K36-5 (PAON) - Body ground

Always

1 MΩ or higher

K36-4 (P-AB) - Body ground

Always

1 MΩ or higher

NG

GO TO STEP 14

OK

11.

CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

(a) Connect the cable to the negative (-) battery terminal.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

*4

Instrument Panel Wire

*a

Front view of wire harness connector

(to Telltale Light Assembly)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K36-10 (IG+) - Body ground

Ignition switch ON

11 to 14 V

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NG

REPLACE WIRE HARNESS OR BATTERY

OK

12.

CHECK PASSENGER AIRBAG ON/OFF INDICATOR

(a) Connect the connector to the telltale light assembly.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

*4

Instrument Panel Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON.

(d) Check the passenger airbag ON/OFF indicator according to the conditions in the table below.

OK:

Terminal Connection

Condition

Specified Condition

K73-35 (PAON) - Body ground

Ignition switch ON

"ON" comes on

K73-34 (P-AB) - Body ground

Ignition switch ON

"OFF" comes on

(e) Turn the ignition switch off.

(f) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NG

REPLACE TELLTALE LIGHT ASSEMBLY 2018 - 2020 MY Camry [03/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: TELLTALE LIGHT ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: TELLTALE LIGHT ASSEMBLY: REMOVAL

OK

13.

CHECK DTC

(a) Connect the connector to the airbag sensor assembly.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON, and wait for at least 60 seconds.

(d) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

OK:

DTC B1660 is not output.

HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.

OK

USE SIMULATION METHOD TO CHECK 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

NG

REPLACE AIRBAG SENSOR ASSEMBLY 2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

14.

CHECK INSTRUMENT PANEL WIRE

(a) Disconnect the connector from the instrument panel junction block assembly.

*1

Instrument Panel Junction Block Assembly

*2

Airbag Sensor Assembly

*3

Telltale Light Assembly

*4

Instrument Panel Wire

*5

Service Wire

-

-

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

*c

Front view of wire harness connector

(to Telltale Light Assembly)

-

-

(b) Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-8 (PAON) - 3A-46 (P-AB)

Always

Below 1 Ω

(d) Disconnect the service wire from connector B.

(e) Using a service wire, connect terminals 5 (PAON) and 4 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(f) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-29 (PAON) - 3A-51 (P-AB)

Always

Below 1 Ω

(g) Disconnect the service wire from connector E.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-8 (PAON) - Body ground or other terminals

Always

1 MΩ or higher

3A-29 (PAON) - Body ground or other terminals

Always

1 MΩ or higher

3A-46 (P-AB) - Body ground or other terminals

Always

1 MΩ or higher

3A-51 (P-AB) - Body ground or other terminals

Always

1 MΩ or higher

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE