| 
                     
                        | Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012SN2 |  
                        | Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 06/2017] |  
                        | Title: DOOR LOCK: DOOR CONTROL RECEIVER: REMOVAL; 2018 MY Camry [03/2017 - 06/2017] |  REMOVALCAUTION / NOTICE / HINTThe necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during door control and tire pressure warning ECU and receiver or electrical key and tire pressure warning ECU and receiver removal/installation are shown below. 
                     
                        
                        
                        
                        
                     
                     
                        
                           | Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |  
                           | Disconnect cable from negative battery terminal | Perform steering sensor zero point calibration | Lane departure alert system (w/ Steering Control) | 
                                 
                                    
                                       
                                          ![2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)  |  
                           | Pre-collision system |  
                           | Memorize steering angle neutral point | Parking assist monitor system | 
                                 
                                    
                                       
                                          ![2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)  |  
                           | 
                                 
                                    
Door control and tire pressure warning ECU and receiver
Electrical key and tire pressure warning ECU and receiver
 | 
                                 
                                    
Register transmitter ID
Initialize tire pressure warning system
 | 
                                 
                                    
When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
Tire pressure warning function
 | 
                                 
                                    
                                       
                                          ![2018 MY Camry [03/2017 - 06/2017]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: REGISTRATION](/t3Portal/stylegraphics/info.gif) for Registration 
                                 
                                    
                                       
                                          ![2018 MY Camry [03/2017 - 06/2017]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif) for Initialization |  CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.   Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)  NOTICE: When replacing the door control and tire pressure warning ECU and receiver or electrical key and tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal. Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: DATA LIST / ACTIVE TEST](/t3Portal/stylegraphics/info.gif)  PROCEDURE1.   PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work. Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+](/t3Portal/stylegraphics/info.gif)  
                     CAUTION: 
                        
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an airbag deploys for any reason, it may cause a serious injury.
   3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+](/t3Portal/stylegraphics/info.gif)  4. REMOVE REAR SEAT CUSHION ASSEMBLY Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+](/t3Portal/stylegraphics/info.gif)  5. REMOVE REAR SEAT CUSHION LOCK HOOK Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+](/t3Portal/stylegraphics/info.gif)  6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH HINT: Use the same procedure as for the LH side. Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+](/t3Portal/stylegraphics/info.gif)  7. REMOVE REAR SIDE SEATBACK ASSEMBLY RH HINT: Use the same procedure as for the LH side. Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+](/t3Portal/stylegraphics/info.gif)  8. REMOVE INNER ROOF SIDE GARNISH RH HINT: Use the same procedure as for the LH side. Click here
                        
                           
                              ![2018 MY Camry [03/2017 - 06/2017]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+](/t3Portal/stylegraphics/info.gif)  9. REMOVE DOOR CONTROL AND TIRE PRESSURE WARNING ECU AND RECEIVER (w/o Smart Key System) 
                     NOTICE: 
                        
Do not drop, strike or otherwise subject the door control and tire pressure warning ECU and receiver to impact.
If the door control and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
 (b) Disengage the 2 guides. (c) Disconnect the connector to remove the door control and tire pressure warning ECU and receiver. 10. REMOVE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Smart Key System) 
                     NOTICE: 
                        
Do not drop, strike or otherwise subject the electrical key and tire pressure warning ECU and receiver to impact.
If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
 (b) Disengage the 2 guides. (c) Disconnect the connector to remove the electrical key and tire pressure warning ECU and receiver. |