DOOR LOCK: FRONT DOOR LOCK: REMOVAL; 2018 MY Camry [03/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000012SMV
Model Year Start: 2018	Model: Camry	Prod Date Range: [03/2017 - 06/2017]
Title: DOOR LOCK: FRONT DOOR LOCK: REMOVAL; 2018 MY Camry [03/2017 - 06/2017]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
	Perform steering sensor zero point calibration	Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
Front door glass sub-assembly Front door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here

4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

7. REMOVE FRONT ARMREST ASSEMBLY

Click here

8. REMOVE COURTESY LIGHT ASSEMBLY

Click here

9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Click here

11. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here

12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here

13. REMOVE FRONT DOOR PANEL PROTECTOR

Click here

14. REMOVE FRONT DOOR GLASS RUN

Click here

15. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Click here

16. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Click here

17. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Click here

18. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

(a) Disconnect the connector.

*1	Front Door Lock Open Rod
	Remove in this Direction

(b) Using a T30 "TORX" socket wrench, remove the 3 screws.

(c) Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.

(d) When reusing the front door lock with motor assembly:

(1) Remove the door lock wiring harness seal from the front door lock with motor assembly.

19. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY

(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.

(b) Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.

Remove in this Direction

20. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

(a) Remove the front door lock remote control cable assembly as shown in the illustration.

Remove in this Direction

21. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

(a) Remove the front door inside locking cable assembly as shown in the illustration.

Remove in this Direction