Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012SDW
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 09/2019]
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: B15DB; Telematics Transceiver Disconnected; 2018 - 2019 MY Camry [03/2017 - 09/2019]

DTC

B15DB

Telematics Transceiver Disconnected

DESCRIPTION

If the radio and display receiver assembly cannot detect the DCM (telematics transceiver) for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past DCM (telematics transceiver) recognition information (registered information), this DTC will be stored.

The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B15DB

Telematics Transceiver Disconnected

DCM (telematics transceiver) disconnected

  • Harness or connector
  • DCM (telematics transceiver)
  • Radio and display receiver assembly

HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

    Click here 2018 MY Camry [03/2017 - 06/2017]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION 2018 - 2020 MY Camry [06/2017 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.
  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the DCM (telematics transceiver), refer to Registration.

    Click here 2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) POWER SOURCE)

(a) Disconnect the K12 DCM (telematics transceiver) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K12-4 (E) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K12-1 (+B) - K12-4 (E)

Always

11 to 14 V

K12-8 (ACC) - K12-4 (E)

Ignition switch ACC

11 to 14 V

K12-7 (IG2) - K12-4 (E)

Ignition switch ON

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

2.

INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect the K1 radio and display receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K1-11 (USBG) - Body ground

Always

Below 1 Ω

*a

Component without harness connected

(Radio and Display Receiver Assembly)

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K1-10 (USBV) - K1-11 (USBG)

Ignition switch ON

4.75 to 5.25 V

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 MY Camry [03/2017 - 06/2017]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

OK

3.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))

(a) Disconnect the K1 radio and display receiver assembly connector.

(b) Disconnect the K15 DCM (telematics transceiver) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K1-10 (USBV) - K15-5 (USBV)

Always

Below 1 Ω

K1-11 (USBG) - K15-3 (USBG)

Always

Below 1 Ω

K1-10 (USBV) or K15-5 (USBV) - Body ground

Always

10 kΩ or higher

K1-11 (USBG) or K15-3 (USBG) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))

(a) Check the installation condition.

(1) Check the USB communication lines between the radio and display receiver assembly and DCM (telematics transceiver) for any installation or connection problems.

(b) Disconnect the K136 and K1 radio and display receiver assembly connectors.

(c) Disconnect the K15 DCM (telematics transceiver) connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K136-1 (USB+) - K15-2 (USB+)

Always

Below 1 Ω

K136-2 (USB-) - K15-1 (USB-)

Always

Below 1 Ω

K136-3 (USBS) - K15-6 (USBS)

Always

Below 1 Ω

K136-1 (USB+) or K15-2 (USB+) - Body ground

Always

10 kΩ or higher

K136-2 (USB-) or K15-1 (USB-) - Body ground

Always

10 kΩ or higher

K136-3 (USBS) or K15-6 (USBS) - Body ground

Always

10 kΩ or higher

*a

Front view of wire harness connector

(to DCM (telematics transceiver))

*b

Front view of wire harness connector

(to Radio and Display Receiver Assembly)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

REPLACE DCM (TELEMATICS TRANSCEIVER)

(a) Replace the DCM (telematics transceiver) with a new one.

Click here 2018 - 2019 MY Camry [03/2017 - 09/2019]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

(b) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(c) Turn the ignition switch off.

(d) Turn the ignition switch to IG and wait for 90 seconds.

(e) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 MY Camry [03/2017 - 06/2017]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL