Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012SCT
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 -           ]
Title: WIPER / WASHER: WIPER AND WASHER SYSTEM: B1372; Wiper Switch Signal Mismatch between LIN and Line; 2018 - 2024 MY Camry [03/2017 -        ]

DTC

B1372

Wiper Switch Signal Mismatch between LIN and Line

DESCRIPTION

Under normal operation, the windshield wiper motor assembly receives operation signals from the windshield wiper switch assembly via LIN communication.

The windshield wiper motor assembly and windshield wiper switch assembly are also connected via direct line in order to operate the front wipers in HI in an emergency. If the operation signals sent via LIN communication and direct line do not match, this DTC is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

DTC Output from

B1372

Wiper Switch Signal Mismatch between LIN and Line

Detection condition:

  • Battery voltage is 9.5 V or more

Malfunction Status:

  • The operation signals sent via LIN communication and direct line do not match

Malfunction Time:

  • 10 seconds or more
  • Windshield wiper motor assembly
  • Main body ECU (multiplex network body ECU)
  • Steering sensor
  • Harness or connector

Wiper

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*

Click here 2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

  • *: w/ Smart Key System

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Wiper / Trouble Codes.

(e) Clear the DTCs.

Body Electrical > Wiper > Clear DTCs

NEXT

2.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Wait 10 seconds or more.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / Wiper / Trouble Codes.

(f) Check for DTCs.

Body Electrical > Wiper > Trouble Codes

Result

Proceed to

DTC B1372 is not output

A

DTC B1372 is output

B

A

USE SIMULATION METHOD TO CHECK 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

B

3.

READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Wiper / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Wiper > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Wiper Switch HI (Line)

Front wiper switch HI position signal (direct line)

OFF or ON

OFF: Front wiper switch not in HI position

ON: Front wiper switch in HI position

-

Body Electrical > Wiper > Data List

Tester Display

Wiper Switch HI (Line)

OK:

The Techstream display is normal.

NG

GO TO STEP 7

OK

4.

READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / Steering Angle Sensor / Data List.

(e) Read the Data List according to the display on the Techstream.

Chassis > Steering Angle Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Wiper Hi Switch

Front wiper switch HI position signal

OFF or ON

OFF: Front wiper switch not in HI position

ON: Front wiper switch in HI position

-

Chassis > Steering Angle Sensor > Data List

Tester Display

Wiper Hi Switch

OK:

The Techstream display is normal.

NG

REPLACE STEERING SENSOR 2018 MY Camry [03/2017 - 06/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL

OK

5.

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)

(a) Disconnect the K51 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the A31 windshield wiper motor assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K51-3 (LIN3) - A31-2 (LIN)

Always

Below 1 Ω

K51-3 (LIN3) or A31-2 (LIN) - Body ground

Always

10 kΩ Higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*a

Component without harness connected

(Main Body ECU (Multiplex Network Body ECU)

(a) Check for pulses according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K51-3 (LIN3) - Body ground

Ignition switch off

Below 1 V

Ignition switch ON

Pulse generation

OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2018 MY Camry [03/2017 - 06/2017]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

7.

CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER MOTOR ASSEMBLY)

(a) Disconnect the K71 steering sensor connector.

(b) Disconnect the A31 windshield wiper motor assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K71-2 (2S) - A31-3 (2S)

Always

Below 1 Ω

K71-2 (2S) or A31-3 (2S) - Body ground

Always

10 kΩ Higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

INSPECT STEERING SENSOR

*a

Component without harness connected

(Steering Sensor)

-

-

(a) Remove the steering sensor.

Click here 2018 MY Camry [03/2017 - 06/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K71-2 (2S) - z6-27 (+2)

Always

Below 1 Ω

OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPLACE STEERING SENSOR 2018 MY Camry [03/2017 - 06/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL