| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012S7E |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 10/2020] |
| Title: PRE-COLLISION: PRE-COLLISION SYSTEM: DATA LIST / ACTIVE TEST; 2018 - 2020 MY Camry [03/2017 - 10/2020] | ||
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Pre-Collision 2 > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Turn Light RH |
Turn signal switch (right) status |
ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
|
Turn Light LH |
Turn signal switch (left) status |
ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
|
PCS OFF Switch |
Pre-collision system on/off status |
ON or OFF |
ON: Pre-collision system on OFF: Pre-collision system off |
- |
|
Pre-Collision Safety Warning Buz |
Pre-collision system warning buzzer |
Valid or Inval |
Valid: Pre-collision system warning buzzer operation possible Inval: Pre-collision system warning buzzer operation not possible |
- |
|
Pre-Collision Brake |
Pre-collision braking function |
Valid or Inval |
Valid: Pre-collision braking operation possible Inval: Pre-collision braking operation not possible |
- |
|
PBA Start |
Pre-collision brake assist activation signal |
OFF, Standby, Assist Lv1 or Assist Lv2 |
OFF: Pre-collision brake assist not operating Standby: Brake pedal not depressed during pre-collision brake assist operation Assist Lv1: Brake pedal depressed during pre-collision brake assist operation Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation |
Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal) |
|
Brake Assist Standby |
- |
- |
- |
Not applicable to this vehicle |
|
Pre-Collision Brake Control |
Pre-collision braking operational status |
ON or OFF |
ON: Pre-collision braking operating OFF: Pre-collision braking not operating |
- |
|
AVS Start |
- |
- |
- |
Not applicable to this vehicle |
|
VGRS Start |
- |
- |
- |
Not applicable to this vehicle |
|
PBA Control |
Pre-collision brake assist operational status |
Valid or Invalid |
Valid: Pre-collision brake assist control operation possible Invalid: Pre-collision brake assist control operation not possible |
- |
|
Pre-Collision Safety Brake Ind |
Pre-collision system alarm warning message status |
ON or OFF |
ON: Displayed OFF: Not displayed |
"BRAKE!" is displayed |
|
PCS Crash Alarm Buzzer |
Pre-collision system warning buzzer status |
ON or OFF |
ON: Pre-collision system warning buzzer sounding OFF: Pre-collision system warning buzzer not sounding |
- |
|
Front Radar-Dirt History |
Millimeter wave radar sensor assembly dirt history |
ON or OFF |
ON: History of excessive dirt OFF: No history of excessive dirt |
- |
|
Front Radar-Environment Hist |
Millimeter wave radar sensor assembly high temperature history |
Good or Bad |
Good: No history of high temperature Bad: History of high temperature |
- |
|
Front Radar-Temperature Malfunction History |
Millimeter wave radar sensor assembly abnormal temperature history |
ON or OFF |
ON: History of abnormal temperature OFF: No history of abnormal temperature |
- |
|
Front Radar-Low Voltage History |
Millimeter wave radar sensor assembly low voltage history |
ON or OFF |
ON: History of low voltage OFF: No history of low voltage |
If the engine starts 1 second or more after the ignition switch was turned to ON (IG), this item may change to ON. |
|
Front Recognition Camera-Blockage History |
Forward recognition camera obstruction history |
ON or OFF |
ON: History of being obstructed OFF: No history of being obstructed |
- |
|
Front Recognition Camera-Malfunction History |
Forward recognition camera system unavailable history |
ON or OFF |
ON: History of being unavailable OFF: No history of being unavailable |
- |
|
Destination Variation No |
Destination country for millimeter wave radar sensor assembly |
Destination Variation No or Not Available |
Destination Variation No |
- |
|
Control Mode |
ECU control mode status |
Normal or Check Mode |
Normal: Normal operation Check Mode: Operating in control mode |
- |
|
PCS Operation State Retention Setting |
PCS operation state retention setting customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
|
PCS Alarm Activation Distance Retention Setting 1 |
PCS alarm activation distance retention setting 1 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
|
PCS Alarm Activation Distance Retention Setting 2 |
PCS alarm activation distance retention setting 2 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
|
PCS Alarm Activation Distance Retention Setting 3 |
PCS alarm activation distance retention setting 3 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
|
The Number of DTCs |
Number of trouble codes |
0 to 255 |
Number of DTCs will be displayed |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Pre-Collision 2 > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
PCS Crash Alarm Buzzer |
Pre-collision system warning buzzer |
ON / OFF |
Test possible with ignition switch ON, vehicle stopped |
|
|