BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR: INSTALLATION; 2018 MY Camry [03/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000012S51
Model Year Start: 2018	Model: Camry	Prod Date Range: [03/2017 - 06/2017]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR: INSTALLATION; 2018 MY Camry [03/2017 - 06/2017]

INSTALLATION

PROCEDURE

1. INSTALL BRAKE ACTUATOR BOLT CUSHION

(a) Install the brake actuator bolt cushion to the brake actuator bracket assembly.

2. INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

(a) Install the No. 2 brake actuator case collar to the brake actuator bolt cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bolt cushion.

3. INSTALL BRAKE ACTUATOR ASSEMBLY

(a) Install the brake actuator assembly to the brake actuator bracket assembly.

(b) Tighten the 2 nuts and install the bolt.

Torque:

6.5 N·m {66 kgf·cm, 58 in·lbf}

NOTICE:

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator assembly when carrying it.
Tighten the bolt and 2 nuts in the order shown in the illustration.

4. INSTALL BRAKE ACTUATOR WITH BRACKET

(a) Temporarily install the brake actuator with bracket to the vehicle body.

NOTICE:

Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Be careful not to allow any brake fluid to enter the connector.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator with bracket when carrying it.

HINT:

Install the brake actuator with bracket while avoiding the brake lines.
After temporarily installing the brake actuator with bracket to the vehicle body, confirm that the cushion is contacting the upper side of the side member.

*a	Stud Bolt
*b	Cushion
*c	Side Member

(b) Install the 2 bolts and nut in the order shown in the illustration.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

HINT:

Install the 2 bolts from the bottom of the vehicle.

(d) Engage the clamp to install a new brake tube clamp.

(e) Return the front No. 3 brake tube to its original position.

NOTICE:

Do not apply excessive force to the front No. 3 brake tube.

(f) Temporarily install the front No. 3 brake tube to the front flexible hose.

NOTICE:

Do not kink or damage the front No. 3 brake tube.
Do not allow any foreign matter such as dirt or dust to enter the front No. 3 brake tube from the connecting parts.

(g) Engage the clamp to connect the front No. 3 brake tube.

NOTICE:

Do not kink or damage the front No. 3 brake tube.

(h) Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:

Do not kink or damage the brake line.
Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

*a	To Front Wheel Cylinder Assembly LH

(i) Using a union nut wrench, fully tighten the brake line.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake line.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a	Torque Wrench Fulcrum Length
*b	Union Nut Wrench

(j) Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:

Do not kink or damage the brake line.
Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

*a	To Rear Wheel Cylinder Assembly RH

(k) Using a union nut wrench, fully tighten the brake line.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake line.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a	Torque Wrench Fulcrum Length
*b	Union Nut Wrench

(l) Temporarily tighten the 4 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:

Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

*a	From 1st Chamber of Brake Master Cylinder Sub-assembly
*b	From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c	To Front Wheel Cylinder Assembly RH
*d	To Rear Wheel Cylinder Assembly LH

(m) Using a union nut wrench, fully tighten each brake line.

Torque:

Specified tightening torque (A) :

19.5 N·m {199 kgf·cm, 14 ft·lbf}

Specified tightening torque (B) :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake lines.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
(A): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
(B): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a	Torque Wrench Fulcrum Length
*b	Union Nut Wrench

(n) Using a union nut wrench, fully tighten the front No. 3 brake tube while holding the front flexible hose with a wrench.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the front No. 3 brake tube.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a	Torque Wrench Fulcrum Length
*b	Union Nut Wrench

(o) Connect the connector to the brake actuator assembly and lock the lock lever.

	Connect the connector
	Lock the lock lever

NOTICE:

Make sure that the connector is locked securely.
Make sure that the actuator connector can be connected smoothly.
Do not allow water, oil or dirt to enter the connector.

5. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

(a) Temporarily install the front center upper suspension brace sub-assembly with the 6 bolts and 4 nuts.

(b) Fully tighten the 2 nuts (A).

Torque:

50 N·m {510 kgf·cm, 37 ft·lbf}

Bolt:

Bolt Color	Torque
Black	8.0 Nm (82 kgfcm, 71 in.*lbf)
Silver	8.9 Nm (91 kgfcm, 79 in.*lbf)

Torque:

Nut (B) :

39 N·m {398 kgf·cm, 29 ft·lbf}

(d) Engage the 2 clamps to install the wire harness.

(e) Connect the connector.

6. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

7. INSTALL FRONT WHEEL RH

Click here

8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

9. BLEED BRAKE SYSTEM

Click here

10. PERFORM SYSTEM VARIANT LEARNING AND ACCELERATION SENSOR ZERO POINT CALIBRATION

Click here

11. PERFORM TEST MODE INSPECTION

Click here

12. INSPECT BRAKE ACTUATOR USING TECHSTREAM

Click here

13. CHECK FOR AND CLEAR DTCS

Click here