Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000001DL3Y |
Model Year Start: 2019 |
Model: Sienna |
Prod Date Range: [08/2018 -
] |
Title: SEAT: REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side): DISASSEMBLY; 2019 - 2020 MY Sienna [08/2018 - ] |
DISASSEMBLY
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH
2. REMOVE REAR POWER SEAT SWITCH
3. REMOVE REAR NO. 2 SEAT COVER BEZEL
(b) Disengage the 4 guides and 4 rear No. 2 seat cover bezels.
4. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH
(a) Disengage the 6 clips to remove the rear seatback board sub-assembly LH.
|
|
5. REMOVE REAR SEAT RECLINING COVER LH
(b) Disengage the 2 guides to remove the rear seat reclining cover LH.
6. REMOVE REAR SEAT RECLINING COVER RH
(b) Disengage the 2 guides to remove the rear seat reclining cover RH.
7. REMOVE REAR NO. 2 SEAT LAP BELT ASSEMBLY CENTER WITH INNER LH
8. REMOVE NO. 2 SEAT CUSHION STOPPER
(a) Remove the 2 screws, 2 No. 2 seat cushion stoppers and 2 plate washers.
|
|
9. SEPARATE REAR SEAT WIRE LH
(b) Disengage the 5 clips to open the lower part of the No. 2 seat cushion cover sub-assembly LH.
(c) Disconnect the fold motor connector to separate the 2 clamps and rear seat wire LH.
|
|
10. REMOVE NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH
(a) Remove the 4 bolts to remove the No. 2 seatback frame sub-assembly LH.
|
|
11. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
12. REMOVE REAR SEAT HEADREST ASSEMBLY
(a) Remove the 14 hog rings and 2 clips from the No. 2 seatback cover sub-assembly LH.
|
|
(b) Separate the cable and clamp from the No. 2 seatback frame sub-assembly LH.
|
|
(c) While releasing the lock inside the headrest support with a screwdriver, remove the headrest.
Text in Illustration
HINT:
Tape the screwdriver tip before use.
|
|
13. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
(a) Disengage the 8 claws to remove the 4 rear No. 2 seat headrest support assemblies.
|
|
14. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY LH
(a) Remove the No. 2 seatback cover sub-assembly LH with the No. 2 seatback pad LH from the No. 2 seatback frame sub-assembly LH.
(b) Remove the 6 hog rings to remove the No. 2 seatback cover sub-assembly LH from the No. 2 seatback pad LH.
|
|
15. REMOVE REAR SEAT WIRE LH
(a) Disconnect the 2 fold seat control ECU connectors.
|
|
(b) Disconnect the 2 reclining motor connectors.
(c) Disengage the 3 clamps.
16. REMOVE FOLD SEAT CONTROL ECU
17. REMOVE REAR SEATBACK HINGE COVER
(b) Remove the clip and rear seatback hinge cover.
18. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
19. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY LH
20. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH
(a) Disengage the 6 clips.
|
|
(b) Remove the No. 2 seat cushion cover sub-assembly with the No. 2 seat cushion pad LH from the No. 2 seat cushion frame sub-assembly LH.
(c) Remove the 5 hog rings.
HINT:
Pull the straps of the No. 2 seat cushion cover sub-assembly LH through the openings in the No. 2 seat cushion pad LH.
|
|
(d) Remove the No. 2 seat cushion cover sub-assembly LH from the No. 2 seat cushion pad LH.
21. REMOVE REAR SEAT COVER
(a) Disengage the 2 clamps to separate the wire harness from the rear seat cover.
|
|
(b) Remove the 2 screws and rear seat cover.
22. REMOVE NO. 2 SEAT CUSHION SPRING ASSEMBLY LH
(a) Remove the 3 No. 3 rear seat protectors.
|
|
(b) Remove the No. 2 seat cushion spring assembly LH.
|
|
|