SEAT: REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side): DISASSEMBLY; 2019 - 2020 MY Sienna [08/2018

Last Modified: 04-05-2023	6.11:8.1.0	Doc ID: RM100000001DL3U
Model Year Start: 2019	Model: Sienna	Prod Date Range: [08/2018 - ]
Title: SEAT: REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side): DISASSEMBLY; 2019 - 2020 MY Sienna [08/2018 - ]

DISASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

Pull the seatback strap to raise the seatback.

PROCEDURE

1. REMOVE REAR NO. 2 SEAT COVER BEZEL

(a) Remove the 2 screws.

(b) Disengage the 2 guides to remove the 2 rear No. 2 seat cover bezels.

2. REMOVE REAR SEATBACK LOCK STRIKER COVER

(a) Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws to remove the rear seatback lock striker cover.

Text in Illustration

*1	Protective Tape

3. REMOVE HANDLE 3RD SEAT

(a) Remove the 2 screws.

(b) Disengage the 3 guides to separate the handle 3rd seat.

4. REMOVE REAR SEATBACK LOCK CONTROL BEZEL

(a) Remove the screw.

(b) Disengage the guide to remove the rear seatback lock control bezel.

5. REMOVE REAR SEAT RECLINING COVER LH

(a) Disengage the 5 clips to remove the rear seatback board cover RH.

(b) Remove the 2 screws.

6. REMOVE REAR SEAT RECLINING COVER RH

(a) Remove the 2 screws.

(b) Disengage the 2 guides to remove the rear seat reclining cover RH.

7. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY RH

8. REMOVE NO. 2 SEAT HEADREST ASSEMBLY

(a) Remove the 8 hog rings and 2 clips.

(b) Remove the 3 hog rings.

(c) Remove the clip to pass the No. 2 seat reclining release handle sub-assembly through the No. 2 seatback cover with pad RH.

(d) Using a screwdriver with its tip wrapped in protective tape, release the lock inside the headrest support to remove the No. 2 seat headrest assembly.

Text in Illustration

*1	Protective Tape

HINT:

When removing the headrest, turn back the No. 2 seatback cover with pad RH and make sure the cable attached to the headrest assembly does not catch on anything inside the No. 2 seatback frame sub-assembly RH.

9. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

(a) Disengage the 4 claws to remove the 2 rear No. 2 seat headrest support assemblies.

10. REMOVE NO. 2 SEATBACK COVER WITH PAD RH

(a) Remove the No. 2 seatback cover with pad RH.

11. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

(a) Remove the 6 hog rings and No. 2 seatback cover sub-assembly RH.

12. REMOVE NO. 2 SEATBACK FRAME SUB-ASSEMBLY RH

(a) Disconnect the 3 cable clamps to separate the 2 reclining remote control cable assemblies.

(b) Remove the 4 bolts and No. 2 seatback frame sub-assembly RH.

13. REMOVE NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY

(a) Remove the nut, No. 2 seat reclining release handle sub-assembly and reclining bolt lock plate.

14. REMOVE NO. 1 RECLINING RELEASE HANDLE SUB-ASSEMBLY

(a) Remove the nut and No. 1 reclining release handle sub-assembly.

15. REMOVE RECLINING CONTROL LINK SUB-ASSEMBLY RH

(a) Remove the 2 nuts.

(b) Disconnect the cable to remove the reclining control link sub-assembly RH.

(d) Remove the screw to rear seatback connecting wire.

16. REMOVE NO. 2 SEAT CUSHION COVER WITH PAD RH

(a) Pass the 2 reclining remote control cable assemblies through the opening in the No. 2 seat cushion cover with pad RH and No. 2 seat cushion frame sub-assembly RH.

(b) Disengage the 6 hooks to remove the No. 2 seat cushion cover with pad RH.

17. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

(a) Remove the 6 hog rings and No. 2 seat cushion cover sub-assembly RH.

18. REMOVE RECLINING REMOTE CONTROL CABLE ASSEMBLY

(a) Disconnect the 6 cable clamps to remove the reclining remote control cable assembly.

(b) Disconnect the 4 cable clamps to remove the reclining remote control cable assembly.

19. REMOVE REAR SEAT CUSHION

(a) Remove the 2 rear seat cushions.

20. REMOVE NO. 2 SEAT HINGE COVER

(a) Remove the 2 screws.

(b) Disengage the guide to remove the No. 2 seat hinge cover.