- Stop light switch assembly
- Harness or connector
- ECM
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000001918U |
| Model Year Start: 2018 | Model: Sienna | Prod Date Range: [11/2017 - ] |
| Title: CRUISE CONTROL: CRUISE CONTROL SYSTEM: P057162; Brake Switch "A" Signal Compare Failure; 2018 - 2020 MY Sienna [11/2017 - ] | ||
|
DTC |
P057162 |
Brake Switch "A" Signal Compare Failure |
DESCRIPTION
When the brake pedal is depressed, stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels the cruise control system.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
P057162 |
Brake Switch "A" Signal Compare Failure |
Vehicle Condition: Ignition switch to ON cruise control main switch on Malfunction Status: Stop light switch assembly malfunction input signal |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
|
1. |
CHECK TERMINAL VOLTAGE (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND) |
|
(a) Disconnect the stop light switch assembly connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A58-2 - Body ground |
Always |
11 to 14 V |
|
A58-4 - Body ground |
Ignition switch ON |
11 to 14 V |
|
A58-4 - Body ground |
Ignition switch off |
Below 1 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY) |
(a) Disconnect the A69 ECM connector.
(b) Disconnect the A58 stop light switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A69-42 (ST1-) - A58-3 |
Always |
Below 1 Ω |
|
A69-27 (STP) - A58-1 |
Always |
Below 1 Ω |
|
A69-42 (ST1-) or A58-3 - Body ground |
Always |
10 kΩ or higher |
|
A69-27 (STP) or A58-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
REPLACE STOP LIGHT SWITCH ASSEMBLY |
(a) Replace the stop light switch assembly.
(See page
![2016 - 2020 MY Sienna [12/2015 - ]; LIGHTING (EXT): STOP LIGHT SWITCH: REMOVAL](/t3Portal/stylegraphics/info.gif)
)
|
|
4. |
CHECK FOR DTCs |
(a) Clear the DTCs.
(See page
)
(b) Perform the following to make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the malfunction cannot be detected.
(1) Turn the cruise control system on using the cruise control main switch (ON/OFF).
(c) Check for DTCs.
(See page
)
Result |
Proceed to |
|---|---|
|
DTC P057162 is not output |
A |
|
DTC P057162 is output |
B |
| A |
|
END (STOP LIGHT SWITCH ASSEMBLY WAS DEFECTIVE) |
| B |
|
|
|