Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018Z6J
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 -           ]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: Speed Signal Circuit; 2018 - 2020 MY Sienna [11/2017 -        ]

Speed Signal Circuit

DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU, which uses this information to create the vehicle speed sensor signal*1. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2, which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.

  • *1: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.

HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occurs:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.
  • When replacing the DCM (telematics transceiver), be sure to replace it with a new one (w/ Manual (SOS) Switch).

PROCEDURE

1.

INSPECT COMBINATION METER ASSEMBLY (INPUT VOLTAGE)

(a) Disconnect the combination meter assembly connector.

*a

Front view of wire harness connector

(to Combination Meter Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D145-3 (+S) - Body ground

Ignition switch ON

4.5 to 14 V

HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.

NG

GO TO STEP 5

OK

2.

INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

(a) Disconnect the brake actuator assembly (skid control ECU) connector.

*a

Front view of wire harness connector

(to Brake Actuator Assembly (Skid Control ECU))

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

A75-14 (SP1) - Body ground

Ignition switch ON

11 to 14 V

NG

GO TO STEP 4

OK

3.

INSPECT BRAKE ACTUATOR ASSEMBLY (INPUT WAVEFORM)

(a) Check the input waveform.

(1) Remove the combination meter assembly with the connector(s) still connected.

(2) Connect an oscilloscope to terminal D145-4 (SI) and body ground.

(3) Turn the ignition switch to ON.

(4) Turn the wheel slowly.

(5) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Tool setting

5 V/DIV., 20 ms./DIV.

Vehicle Condition

Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

*a

Component with harness connected

(Combination Meter Assembly)

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

4.

CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - COMBINATION METER ASSEMBLY)

(a) Disconnect the A75 brake actuator assembly (skid control ECU) connector.

(b) Disconnect the D145 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A75-14 (SP1) - D145-4 (SI)

Always

Below 1 Ω

A75-14 (SP1) or D145-4 (SI) - Body ground

Always

10 kΩ or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the D145 combination meter assembly connector.

(b) Disconnect the 2A instrument panel junction block assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D145-3 (+S) - 2A-30

Always

Below 1 Ω

D145-3 (+S) or 2A-30 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Inspect for a short in the circuit that is connected to the instrument panel junction block assembly connector shown in the wiring diagram.

HINT:

If the voltage is not as specified, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.

(1) Disconnect the 2A and 2F instrument panel junction block assembly connectors.

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

(2) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

2F-27 - Body ground

Ignition switch ON

4.5 to 14 V

2A-29 - Body ground

Ignition switch ON

4.5 to 14 V

2A-28 - Body ground

Ignition switch ON

4.5 to 14 V

Result

Result

Proceed to

Voltage is not as specified in one circuit

A

Voltage is as specified in all circuits

B

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

A

7.

SYSTEM CHECK

(a) Select the circuit for which voltage was not as specified in the previous step 6.

Result

Tester Connection

System that Uses the Circuit

Proceed to

2F-27 - Body ground

SFI system

A

2A-29 - Body ground

Tire pressure warning system

B

2A-28 - Body ground

Smart key system*1, wiper and washer system*2, separate type amplifier system*3, safety connect system*4, navigation system*5, audio and visual system*6

C

  • *1: w/ Smart Key System
  • *2: w/ Rain Sensor
  • *3: for Separate Type Amplifier System
  • *4: w/ Safety Connect System
  • *5: w/ Navigation System
  • *6: w/o Navigation System
B

GO TO STEP 9

C

GO TO STEP 10

A

8.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)

(a) Disconnect the 2F instrument panel junction block assembly connector.

(b) Disconnect the A69 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2F-27 - A69-39 (SPD)

Always

Below 1 Ω

2F-27 or A69-39 (SPD) - Body ground

Always

10 kΩ or higher

OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - TIRE PRESSURE WARNING ECU)

(a) Disconnect the 2A instrument panel junction block assembly connector.

(b) Disconnect the D82 tire pressure warning ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2A-29 - D82-2 (SPD)

Always

Below 1 Ω

2A-29 or D82-2 (SPD) - Body ground

Always

10 kΩ or higher

OK

REPLACE TIRE PRESSURE WARNING ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - JUNCTION CONNECTOR)

(a) Disconnect the 2A instrument panel junction block assembly connector.

(b) Disconnect the D175 junction connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2A-28 - D175-13

Always

Below 1 Ω

2A-28 or D175-13 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

11.

CHECK VEHICLE TYPE

(a) Check vehicle type.

Result

Proceed to

w/ Smart Key System

A

w/o Smart Key System

B

B

GO TO STEP 14

A

12.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

(a) Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

(1) Disconnect the junction connector.

*a

Front view of wire harness connector

(to Junction Connector)

(2) Measure the voltage according to the value(s) in the table below

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D175-17 - Body ground

Ignition switch ON

4.5 to 14 V

OK

GO TO STEP 14

NG

13.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

(a) Disconnect the D175 junction connector.

(b) Disconnect the D89 power management control ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D175-17 - D89-23 (SPD)

Always

Below 1 Ω

D175-17 or D89-23 (SPD) - Body ground

Always

10 kΩ or higher

OK

REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.

CHECK VEHICLE TYPE

(a) Check vehicle type.

Result

Proceed to

w/ Rain Sensor

A

w/o Rain Sensor

B

B

GO TO STEP 17

A

15.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

(a) Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

(1) Disconnect the junction connector.

*a

Front view of wire harness connector

(to Junction Connector)

(2) Measure the voltage according to the value(s) in the table below

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D175-14 - Body ground

Ignition switch ON

4.5 to 14 V

OK

GO TO STEP 17

NG

16.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - WINDSHIELD WIPER RELAY ASSEMBLY)

(a) Disconnect the D175 junction connector.

(b) Disconnect the D78 windshield wiper relay assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D175-14 - D78-19 (SPD)

Always

Below 1 Ω

D175-14 or D78-19 (SPD) - Body ground

Always

10 kΩ or higher

OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.

CHECK VEHICLE TYPE

(a) Check vehicle type.

Result

Proceed to

for Separate Type Amplifier System

A

except Separate Type Amplifier System

B

B

GO TO STEP 20

A

18.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

(a) Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

(1) Disconnect the junction connector.

*a

Front view of wire harness connector

(to Junction Connector)

(2) Measure the voltage according to the value(s) in the table below

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D175-16 - Body ground

Ignition switch ON

4.5 to 14 V

OK

GO TO STEP 20

NG

19.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - STEREO COMPONENT AMPLIFIER ASSEMBLY)

(a) Disconnect the D175 junction connector.

(b) Disconnect the L56 stereo component amplifier assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D175-16 - L56-11 (SPD)

Always

Below 1 Ω

D175-16 or L56-11 (SPD) - Body ground

Always

10 kΩ or higher

OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.

CHECK VEHICLE TYPE

(a) Check vehicle type.

Result

Proceed to

w/ Safety Connect System

A

w/o Safety Connect System

B

B

GO TO STEP 23

A

21.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

(a) Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

(1) Disconnect the junction connector.

*a

Front view of wire harness connector

(to Junction Connector)

(2) Measure the voltage according to the value(s) in the table below

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D175-15 - Body ground

Ignition switch ON

4.5 to 14 V

OK

GO TO STEP 23

NG

22.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

(a) Disconnect the D175 junction connector.

(b) Disconnect the D73 telematics transceiver connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D175-15 - D73-10 (SPDP)

Always

Below 1 Ω

D175-15 or D73-10 (SPDP) - Body ground

Always

10 kΩ or higher

OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.

CHECK VEHICLE TYPE

(a) Check vehicle type.

Result

Proceed to

w/ Navigatiom System

A

w/o Navigatiom System

B

B

GO TO STEP 26

A

24.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

(a) Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

(1) Disconnect the junction connector.

*a

Front view of wire harness connector

(to Junction Connector)

(2) Measure the voltage according to the value(s) in the table below

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D175-18 - Body ground

Ignition switch ON

4.5 to 14 V

OK

GO TO STEP 26

NG

25.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - NAVIGATION ECU)

(a) Disconnect the D175 junction connector.

(b) Disconnect the D199 navigation ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D175-18 - D199-9 (SPD)

Always

Below 1 Ω

D175-18 or D199-9 (SPD) - Body ground

Always

10 kΩ or higher

OK

REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

(a) Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

(1) Disconnect the junction connector.

*a

Front view of wire harness connector

(to Junction Connector)

(2) Measure the voltage according to the value(s) in the table below

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D175-12 - Body ground

Ignition switch ON

4.5 to 14 V

OK

REPLACE JUNCTION CONNECTOR

NG

27.

CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Disconnect the D175 junction connector.

(b) Disconnect the D195 radio and display receiver assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D175-12 - D195-27 (SPD)

Always

Below 1 Ω

D175-12 or D195-27 (SPD) - Body ground

Always

10 kΩ or higher

Result

Result

Proceed to

NG

A

OK (w/ Navigation System)

B

OK (w/o Navigation System)

C

A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY