Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018YBJ
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 -           ]
Title: PRE-COLLISION: PRE-COLLISION SYSTEM: C1A47; Steering Angle Sensor; 2018 - 2020 MY Sienna [11/2017 -        ]

DTC

C1A47

Steering Angle Sensor

DESCRIPTION

The driving support ECU assembly receives steering angle information from the steering sensor. If the driving support ECU assembly detects a steering sensor malfunction, DTC C1A47 will be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1A47

Steering Angle Sensor

While the vehicle is being driven at a speed of 50 km/h (32 mph) or more, the driving support ECU assembly receives a steering sensor malfunction signal continuously for 1 second or more.
  • Vehicle stability control system
  • Skid control ECU (Brake actuator assembly)
  • Driving support ECU assembly

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
  • The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here 2018 - 2020 MY Sienna [11/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

PROCEDURE

1.

CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

Pre-collision system DTC C1A47 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.

(a) Check for DTCs.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: DTC CHECK / CLEAR

Result

Proceed to

Vehicle stability control system DTCs are not output

A

Vehicle stability control system DTCs are output

B
B

GO TO VEHICLE STABILITY CONTROL SYSTEM

A

2.

CHECK FOR DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR

(b) Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

  1. Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.

(c) Check for DTCs.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR

Result

Proceed to

DTC C1A47 is not output

A

DTC C1A47 is output

B
A

USE SIMULATION METHOD TO CHECK

B

3.

REPLACE DRIVING SUPPORT ECU ASSEMBLY

(a) Replace the driving support ECU assembly.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; CRUISE CONTROL: DRIVING SUPPORT ECU: REMOVAL

NEXT

4.

CHECK FOR DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR

(b) Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

  1. Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.

(c) Check for DTCs.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: DTC CHECK / CLEAR

Result

Proceed to

DTC C1A47 is not output

A

DTC C1A47 is output

B
A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)
B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)