- PCV valve and hose
- PCV hose connections
- Gas leak from exhaust system
- Intake system
- Fuel pressure
- Mass air flow meter
- Engine coolant temperature sensor
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM1000000018SMC |
| Model Year Start: 2018 | Model: Sienna | Prod Date Range: [11/2017 - 08/2018] |
| Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P017100,P017200,P017400,P017500,P117000,P117B00; System Too Lean Bank 1; 2018 MY Sienna [11/2017 - 08/2018] | ||
|
DTC |
P017100 |
System Too Lean Bank 1 |
|
DTC |
P017200 |
System Too Rich Bank 1 |
|
DTC |
P017400 |
System Too Lean Bank 2 |
|
DTC |
P017500 |
System Too Rich Bank 2 |
|
DTC |
P117000 |
Fuel Performance/Port Injector |
|
DTC |
P117B00 |
Fuel Performance/Direct Injector |
DESCRIPTION
The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P017100 |
System Too Lean Bank 1 |
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P017200 |
System Too Rich Bank 1 |
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P017400 |
System Too Lean Bank 2 |
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P017500 |
System Too Rich Bank 2 |
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P117000 |
Fuel Performance/Port Injector |
Although a DTC is stored for a rich or lean condition, the amount of fuel trim during direct injection is normal (1 trip detection logic) |
|
Does not come on |
DTC stored |
|
|
P117B00 |
Fuel Performance/Direct Injector |
Although a DTC is stored for a rich or lean condition, the amount of fuel trim during port injection is normal (1 trip detection logic) |
|
Does not come on |
DTC stored |
|
HINT:
- When DTC P017100 or P017400 is stored, the actual air fuel ratio is on the lean side. When DTC P017200 or P017500 is stored, the actual air fuel ratio is on the rich side.
- If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P017100 or P017400 may be stored. The MIL is then illuminated.
- When DTC P117000 or P117B00 is output, it may not be possible to precisely determine whether the port injection or the direct injection is malfunctioning, depending on the conditions. In this case, perform an Active Test (Control the Injection Mode) to determine which injection system is malfunctioning.
MONITOR DESCRIPTION
Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learned value is +35% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.
MONITOR STRATEGY
|
Related DTCs |
P0171: Fuel trim lean (bank 1) P0172: Fuel trim rich (bank 1) P0174: Fuel trim lean (bank 2) P0175: Fuel trim rich (bank 2) P1170: Fuel trim (port injection fail) P117B: Fuel trim (direct injection fail) |
|
Required Sensors/Components (Main) |
Fuel system |
|
Required Sensors/Components (Related) |
Air fuel ratio sensor Mass air flow meter Crankshaft position sensor |
|
Frequency of Operation |
Continuous |
|
Duration |
Within 10 seconds |
|
MIL Operation |
2 driving cycles: P0171, P0172, P0174, P0175 Immediate: P1170, P117B |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
P0010, P0020 (VVT oil control solenoid bank 1, 2) P0011, P0021 (VVT system bank 1, 2 - advance) P0012, P0022 (VVT system bank 1, 2 - retard) P0013, P0023 (Exhaust VVT oil control solenoid bank 1, 2) P0014, P0024 (Exhaust VVT system bank 1, 2 - advance) P0015, P0025 (Exhaust VVT system bank 1, 2 - retard) P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0191, P0192, P0193 (Fuel pressure sensor (for high pressure side)) P0101, P0102, P0103 (Mass air flow meter) P0117, P0118 (Engine coolant temperature sensor) P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0201, P0202, P0203, P0204, P0205, P0206, P062D, P21CF, P21D0, P21D1, P21D2, P21D3, P21D4 (Fuel injector) P0335, P0337, P0338 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P107B, P107C, P107D (Fuel pressure sensor (for low pressure side)) P11EA, P11EB, P11EC, P11ED, P11EE, P11EF, P11F0, P11F1, P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1 (Air-fuel ratio imbalance) |
|
Fuel system status |
Closed loop |
|
Battery voltage |
11 V or higher |
|
Either of the following conditions is met |
1 or 2 |
|
1. Engine speed |
Less than 650 rpm |
|
2. Engine load |
12% or higher |
|
Catalyst monitor |
Not executed |
TYPICAL MALFUNCTION THRESHOLDS
P0171, P0172, P0174 and P0175: Fuel-Trim Lean/Rich
|
EVAP purge-cut |
Executing |
|
Either of the following conditions is met |
1 or 2 |
|
1. Average between short-term fuel trim and long-term fuel trim |
35% or higher (varies with engine coolant temperature) |
|
2. Average between short-term fuel trim and long-term fuel trim |
-35% or less (varies with engine coolant temperature) |
P1170: Fuel Trim (Port Injection Fail)
|
DTCs of fuel system have already been set |
- |
|
EVAP purge-cut |
Executing |
|
Direct injection |
100% |
|
Both of the following conditions are met |
1 and 2 |
|
1. Average between short-term fuel trim and long-term fuel trim |
Less than 35% (varies with engine coolant temperature) |
|
2. Average between short-term fuel trim and long-term fuel trim |
Higher than -35% (varies with engine coolant temperature) |
P117B: Fuel Trim (Direct Injection Fail)
|
DTCs of fuel system have already been set |
- |
|
EVAP purge-cut |
Executing |
|
Port injection |
100% |
|
Both of the following conditions are met |
1 and 2 |
|
1. Average between short-term fuel trim and long-term fuel trim |
Less than 35% (varies with engine coolant temperature) |
|
2. Average between short-term fuel trim and long-term fuel trim |
Higher than -35% (varies with engine coolant temperature) |
CONFIRMATION DRIVING PATTERN
HINT:
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
![2017 - 2020 MY Sienna [08/2016 - ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
- Permanent misfire and fuel system DTCs can only be cleared when performing the universal trip driving pattern when no malfunction is detected.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the Techstream on [A].
- Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
- With the engine warmed up, idle the engine for 2 minutes or more [C].
-
Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
- Enter the following menus: Powertrain / Engine / Trouble Codes [E].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
WIRING DIAGRAM
-
Refer to DTC P010012 for the mass air flow meter circuit.
Click here
-
Refer to DTC P21951D for the air fuel ratio sensor circuit.
Click here
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
-
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
- A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
- A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P017100, P017200, P017400, P017500, P117000 OR P117B00) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTC P017100, P017200, P017400, P017500, P117000 or P117B00 is output |
A |
|
DTC P017100, P017200, P017400, P017500, P117000 and/or P117B00 and other DTCs are output |
B |
HINT:
If any DTCs other than P017100, P017200, P017400, P017500, P117000 or P117B00 are output, troubleshoot those DTCs first.
| B |
|
|
|
2. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION MODE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Start the engine and warm it up.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Port / Data List / Injection Mode, Short FT B1S1, Long FT B1S1, Short FT B2S1 and Long FT B2S1.
(f) Read the values displayed on the Techstream.
OK:
Short FT B1S1 (B2S1) + Long FT B1S1 (B2S1) = Between -19% and 19% (Port Injection)
(g) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / Injection Mode, Short FT B1S1, Long FT B1S1, Short FT B2S1 and Long FT B2S1.
(h) Read the values displayed on the Techstream.
OK:
Short FT B1S1 (B2S1) + Long FT B1S1 (B2S1) = Between -19% and 19% (Direct Injection)
|
Item |
Proceed to |
|
|---|---|---|
|
Port |
Direct |
|
|
OK |
OK |
A |
|
OK |
NG |
B |
|
NG |
OK |
C |
|
NG |
NG |
D |
| B |
|
| C |
|
| D |
|
|
|
3. |
CHECK IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
(a) Has the vehicle run out of fuel in the past?
| YES |
|
DTC CAUSED BY RUNNING OUT OF FUEL |
| NO |
|
|
4. |
READ VALUE USING TECHSTREAM (FUEL PRESSURE (HIGH)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Start the engine and warm it up.
(e) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
(f) Read the values.
Standard:
2400 to 19500 kPag (3000 rpm, engine warmed up, shift lever in P, A/C off).
| NG |
|
|
|
5. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION MODE (DIRECT)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and turn the Techstream on.
(c) Start the engine and warm it up.
(d) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / High Pressure Fuel Pump Duty Ratio (D4), Injection Mode, Short FT B1S1, Long FT B1S1, Short FT B2S1 and Long FT B2S1.
(e) Read the values displayed on the Techstream.
HINT:
The A/C switch and all accessory switches should be off, and the shift lever should be in the P position, and the engine should be fully warmed up.
|
Item |
Proceed to |
|||
|---|---|---|---|---|
|
Injection Mode |
High Pressure Fuel Pump Duty Ratio (D4) |
Short FT B1S1 + Long FT B1S1 |
Short FT B2S1 + Long FT B2S1 |
|
|
Direct |
10% to 40% |
- |
- |
A |
|
40% or higher |
-20% or less |
-20% or less |
B |
|
|
10% or less |
20% or higher |
20% or higher |
||
|
40% or higher |
20% or higher |
20% or higher |
C |
|
|
10% or less |
-20% or less |
-20% or less |
D |
|
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).
Click here
| B |
|
REPLACE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)) |
| C |
|
| D |
|
|
|
6. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION MODE (DIRECT)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and turn the Techstream on.
(c) Start the engine and warm it up.
(d) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / High Pressure Fuel Pump Duty Ratio (D4), Injection Mode, Short FT B1S1, Long FT B1S1, Short FT B2S1 and Long FT B2S1.
(e) Read the values displayed on the Techstream.
HINT:
The A/C switch and all accessory switches should be off, and the shift lever should be in the P position, and the engine should be fully warmed up.
|
Item |
Proceed to |
|||
|---|---|---|---|---|
|
Injection Mode |
High Pressure Fuel Pump Duty Ratio (D4) |
Short FT B1S1 + Long FT B1S1 |
Short FT B2S1 + Long FT B2S1 |
|
|
Direct |
10% to 40% |
-25% or less |
-25% or less |
A |
|
10% to 40% |
30% or higher |
30% or higher |
||
|
10% to 40% |
-25% or less |
-25% to 25% |
B |
|
|
10% to 40% |
25% or higher |
-25% to 25% |
||
|
10% to 40% |
-25% to 25% |
-25% or less |
C |
|
|
10% to 40% |
-25% to 25% |
25% or higher |
||
|
10% to 40% |
-25% to 25% |
-25% to 25% |
D |
|
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).
Click here
| A |
|
REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION (ALL CYLINDERS)) |
| B |
|
REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION (BANK 1)) |
| C |
|
REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION (BANK 2)) |
| D |
|
|
7. |
CHECK MISFIRE COUNT OF DIRECT INJECTION |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Start the engine and warm it up.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.
(f) Read the values displayed on the Techstream.
HINT:
The A/C switch and all accessory switches should be off, and the shift lever should be in the P position, and the engine should be fully warmed up.
|
Injection Mode |
Misfire Count |
Proceed to |
|---|---|---|
|
Direct |
No misfire counts, or misfire counts occur randomly in all cylinders |
A |
|
Misfire counts occur in particular cylinder |
B |
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).
Click here
| B |
|
|
|
8. |
REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) |
(a) Replace the fuel pump assembly (for high pressure side).
Click here
HINT:
Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).
Click here
|
|
9. |
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (DTC P017100, P017200, P017400, P017500, P117000 OR P117B00) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Start the engine and warm it up.
(i) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(j) Enter the following menus: Powertrain / Engine / Trouble Codes.
(k) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P017100, P017200, P017400, P017500, P117000 and/or P117B00 are output |
B |
| A |
|
END |
| B |
|
|
10. |
INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) |
(a) Inspect the injection volume (whether fuel volume is high or low, and whether injection pattern is poor).
Click here
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).
Click here
| OK |
|
| NG |
|
|
11. |
CHECK PCV HOSE CONNECTIONS |
(a) Check the PCV hose connections.
Click here
OK:
PCV valve and hose are connected correctly and are not damaged.
| NG |
|
REPAIR OR REPLACE PCV HOSE |
|
|
12. |
CHECK INTAKE SYSTEM |
(a) Check the intake system for vacuum leaks.
Click here
OK:
No leaks from the intake system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click here
| NG |
|
REPAIR OR REPLACE INTAKE SYSTEM |
|
|
13. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and turn the Techstream on.
(c) Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
(d) Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2.
(f) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (change the fuel injection volume).
(g) Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2) displayed on the Techstream.
HINT:
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
- If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
Standard:
|
Techstream Display (Sensor) |
Injection Volume |
Status |
Voltage |
|---|---|---|---|
|
A/F (O2) Sensor Voltage B1S1 A/F (O2) Sensor Voltage B2S1 (Air fuel ratio) |
12.5% |
Rich |
Below 3.1 V |
|
-12.5% |
Lean |
Higher than 3.4 V |
|
|
O2 Sensor Voltage B1S2 O2 Sensor Voltage B2S2 (Heated oxygen) |
12.5% |
Rich |
Higher than 0.55 V |
|
-12.5% |
Lean |
Below 0.4 V |
|
Status of A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 |
Status of O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 |
Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition |
Suspected Trouble Area |
Proceed to |
|---|---|---|---|---|
|
Lean/Rich |
Lean/Rich |
Normal |
- |
A |
|
Lean |
Lean |
Actual air fuel ratio lean |
|
|
|
Rich |
Rich |
Actual air fuel ratio rich |
|
|
|
Lean |
Lean/Rich |
Air fuel ratio sensor malfunction |
|
B |
|
Rich |
Lean/Rich |
Air fuel ratio sensor malfunction |
|
- Lean: During Control the Injection Volume for A/F Sensor of the Active Test, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2) is consistently below 0.4 V.
- Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 is consistently higher than 0.55 V.
- Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.
HINT:
Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1, O2 Sensor Voltage B1S2, A/F (O2) Sensor Voltage B2S1 or O2 Sensor Voltage B2S2].
Click here
| B |
|
|
|
14. |
READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
(e) Read the Data List twice, when the engine is both cold and warmed up.
Standard:
|
Techstream Display |
Condition |
Specified Condition |
|---|---|---|
|
Coolant Temperature |
Cold engine |
Same as ambient air temperature |
|
Warm engine |
Between 75 and 100°C (167 and 212°F) |
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here
| NG |
|
|
|
15. |
READ VALUE USING TECHSTREAM (MASS AIR FLOW SENSOR) |
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.
(e) Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.
(f) Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
Standard:
|
Techstream Display |
Condition |
Specified Condition |
|---|---|---|
|
Mass Air Flow Sensor |
Engine warmed up Shift lever position: P A/C: Off Engine Speed: 3000 rpm |
Between 10.6 gm/sec and 15.8 gm/sec |
| NG |
|
|
|
16. |
CHECK FOR EXHAUST GAS LEAK |
(a) Check for exhaust gas leaks.
OK:
No gas leaks.
HINT:
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click here
| NG |
|
REPAIR OR REPLACE EXHAUST SYSTEM |
|
|
17. |
CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE) |
(a) Check the fuel pressure (for low pressure side).
Click here
| OK |
|
|
|
18. |
CHECK FUEL LINE |
(a) Check the fuel lines for leaks or blockage.
| OK |
|
| NG |
|
REPAIR OR REPLACE FUEL SYSTEM |
|
19. |
INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
(a) Inspect the air fuel ratio sensor.
Click here
HINT:
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click here
| NG |
|
|
|
20. |
CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
(a) Disconnect the B14 and B13 air fuel ratio sensor connectors.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B14-1 (HA1A) - B67-52 (HA1A) |
Always |
Below 1 Ω |
|
B14-3 (A1A+) - B67-125 (A1A+) |
Always |
Below 1 Ω |
|
B14-4 (A1A-) - B67-126 (A1A-) |
Always |
Below 1 Ω |
|
B13-1 (HA2A) - B67-17 (HA2A) |
Always |
Below 1 Ω |
|
B13-3 (A2A+) - B67-123 (A2A+) |
Always |
Below 1 Ω |
|
B13-4 (A2A-) - B67-124 (A2A-) |
Always |
Below 1 Ω |
|
B14-1 (HA1A) or B67-52 (HA1A) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B14-3 (A1A+) or B67-125 (A1A+) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B14-4 (A1A-) or B67-126 (A1A-) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B13-1 (HA2A) or B67-17 (HA2A) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B13-3 (A2A+) or B67-123 (A2A+) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B13-4 (A2A-) or B67-124 (A2A-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
21. |
REPLACE AIR FUEL RATIO SENSOR |
(a) Replace the air fuel ratio sensor.
Click here
HINT:
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click here
|
|
22. |
CONFIRM CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (DTC P017100, P017200, P017400, P017500, P117000 OR P117B00) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Start the engine and warm it up.
(i) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(j) Enter the following menus: Powertrain / Engine / Trouble Codes.
(k) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P017100, P017200, P017400, P017500, P117000 and/or P117B00 are output |
B |
| A |
|
END |
|
|
23. |
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION) |
(a) Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.
Click here
HINT:
Repair any problems.
|
|
24. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P017400, P017500, P117000 OR P117B00) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Start the engine and warm it up.
(i) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(j) Enter the following menus: Powertrain / Engine / Trouble Codes.
(k) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P017100, P017200, P017400, P017500, P117000 and/or P117B00 are output |
B |
| A |
|
END |
|
|
25. |
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
(a) Disconnect the B56 mass air flow meter connector.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B56-3 (5V) - B67-90 (VC) |
Always |
Below 1 Ω |
|
B56-1 (FG) - B67-116 (VG) |
Always |
Below 1 Ω |
|
B56-2 (E2G) - B67-115 (E2G) |
Always |
Below 1 Ω |
|
B56-3 (5V) or B67-90 (VC) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B56-1 (FG) or B67-116 (VG) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B56-2 (E2G) or B67-115 (E2G) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
26. |
REPLACE MASS AIR FLOW METER |
(a) Replace the mass air flow meter.
Click here
HINT:
- If the result of the inspection performed in step 15 indicated no problem, proceed to the next step without replacing the mass air flow meter.
-
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click here
|
|
27. |
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Start the engine and warm it up.
(i) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(j) Enter the following menus: Powertrain / Engine / Trouble Codes.
(k) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P017100, P017200, P017400, P017500, P117000 and/or P117B00 are output |
B |
| A |
|
END |
| B |
|
|
|