Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM1000000018QYR |
Model Year Start: 2018 |
Model: Sienna |
Prod Date Range: [11/2017 -
] |
Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: B1543; Extension Module Disconnected 2; 2018 - 2020 MY Sienna [11/2017 - ] |
DTC
|
B1543
|
Extension Module Disconnected 2
|
DESCRIPTION
If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned ON and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.
HINT:
The Navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the Navigation system will not operate normally.
DTC Code
|
DTC Detection Condition
|
Trouble Area
|
B1543
|
Navigation ECU disconnected
|
-
Navigation ECU
-
Radio and display receiver assembly
-
No. 1 navigation wire
-
Harness or connector
|
HINT:
This DTC may be stored due to environmental reasons such as electrical noise or interference.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Inspect the fuses for circuits related to this system before performing the following procedure.
-
When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
-
A communication malfunction DTC is stored.
-
The radio and display receiver assembly or navigation ECU may not operate normally.
PROCEDURE
(a) Turn the ignition switch ON and wait for 90 seconds.
(b) Press the "MAP" switch and check that the map screen is displayed normally.
Result
|
Proceed to
|
Map screen is displayed normally
|
A
|
Map screen is not displayed normally
|
B
|
HINT:
-
This DTC may be stored due to environmental reasons such as electrical noise or interference.
-
Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)
B
|
|
|
(a) Clear the DTCs.
(b) Turn the ignition switch off.
(c) Turn the ignition switch ON and wait for 90 seconds.
(d) Recheck for DTCs and check that no DTCs are output.
OK:
No DTCs are output.
NG
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)
|
(a) Disconnect the navigation ECU connector.
|
|
*a
|
Front view of wire harness connector
(to Navigation ECU)
|
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D199-23 (GND) - Body ground
|
Always
|
Below 1 Ω
|
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
D199-10 (+B) - Body ground
|
Always
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
|
(a) Disconnect the V14 navigation ECU connector.
|
|
*a
|
Front view of wire harness connector
(to Radio and Display Receiver Assembly)
|
*b
|
Front view of wire harness connector
(to Navigation ECU)
|
|
|
(b) Disconnect the V12 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
V14-4 (US4+) - V12-1 (US4+)
|
Always
|
Below 1 Ω
|
V14-5 (US4-) - V12-2 (US4-)
|
Always
|
Below 1 Ω
|
V14-6 (UGD4) - V12-3 (UGD4)
|
Always
|
Below 1 Ω
|
OK
|
|
|
5.
|
REPLACE NAVIGATION ECU
|
(a) Replace the navigation ECU with a new one.
Click here
NEXT
|
|
|
(a) Clear the DTCs.
(b) Turn the ignition switch off.
(c) Turn the ignition switch ON and wait for 90 seconds.
(d) Recheck for DTCs and check that no DTCs are output.
OK:
No DTCs are output.
OK |
|
END (NAVIGATION ECU IS DEFECTIVE)
|
|