Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018KFB
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: Slip Indicator Light does not Come ON; 2018 - 2020 MY Sienna [11/2017 -        ]

Slip Indicator Light does not Come ON

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

WIRING DIAGRAM

Refer to Slip Indicator Light Remains ON (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: Slip Indicator Light Remains ON ).

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: CALIBRATION ).

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication system DTCs are output (See page 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2019 - 2020 MY Sienna [08/2018 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM ).

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B

B

INSPECT CAN COMMUNICATION SYSTEM

A

2.

PERFORM ACTIVE TEST USING TECHSTREAM (SLIP INDICATOR LIGHT)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Select the Active Test on the Techstream.

(f) According to the display on the Techstream, perform the Active Test.

ABS/VSC/TRAC

Tester Display

Measurement Item

Control Range

Diagnostic Note

Slip Indicator Light

Slip indicator light

Indicator light ON/OFF

Can be observed on the combination meter assembly

(g) When performing the Slip Indicator Light Active Test, check Slip Indicator Light in the Data List.

ABS/VSC/TRAC

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Slip Indicator Light

Slip indicator light / ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Result

Proceed to

Slip indicator light in the Data List does not change using the Active Test.

A

Slip indicator light in the Data List turns ON/OFF using the Active Test.

B

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: PROBLEM SYMPTOMS TABLE ).

A

REPLACE BRAKE ACTUATOR ASSEMBLY

B

3.

INSPECT COMBINATION METER ASSEMBLY

(a) Turn the ignition switch off.

(b) Perform Active Test of the combination meter assembly using the Techstream.

(c) Check the combination meter assembly.

OK:

The slip indicator light turns on or off in accordance with the Techstream.

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: PROBLEM SYMPTOMS TABLE ).

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

INSPECT METER / GAUGE SYSTEM