Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018KFA
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: Slip Indicator Light Remains ON; 2018 - 2020 MY Sienna [11/2017 -        ]

Slip Indicator Light Remains ON

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRAC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: DIAGNOSIS SYSTEM ).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: CALIBRATION ).
  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication system DTCs are output (See page 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2019 - 2020 MY Sienna [08/2018 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM ).

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B

B

INSPECT CAN COMMUNICATION SYSTEM

A

2.

CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

(a) Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

OK

3.

INSPECT BATTERY POSITIVE TERMINAL

(a) Check the battery voltage.

Standard Voltage:

11 to 14 V

NG

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

OK

4.

CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

(a) Disconnect the skid control ECU (brake actuator assembly) connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

A75-12 (IG1) - Body ground

Ignition switch ON

10.5 to 16 V

Text in Illustration

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Actuator Assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

OK

5.

CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

(a) Turn the ignition switch off.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A75-25 (GND1) - Body ground

Always

Below 1 Ω

Text in Illustration

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Actuator Assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

OK

6.

READ VALUE USING TECHSTREAM (SLIP INDICATOR LIGHT)

(a) Reconnect the A75 skid control ECU (brake actuator assembly) connector.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Select the Data List using the Techstream (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: DATA LIST / ACTIVE TEST ).

ABS/VSC/TRAC

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Slip Indicator Light

Slip indicator light / ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

(f) Check the Techstream display condition of the slip indicator light.

Result

Proceed to

Display of the Data List remains ON.

A

Display of the Data List remains OFF.

B

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: PROBLEM SYMPTOMS TABLE ).

A

REPLACE BRAKE ACTUATOR ASSEMBLY

B

INSPECT METER / GAUGE SYSTEM