Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM1000000018KEJ |
Model Year Start: 2018 |
Model: Sienna |
Prod Date Range: [11/2017 -
] |
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C1413,C1414; Front Speed Sensor RH Output Malfunction; 2018 - 2020 MY Sienna [11/2017 - ] |
DTC
|
C1413
|
Front Speed Sensor RH Output Malfunction
|
DTC
|
C1414
|
Front Speed Sensor LH Output Malfunction
|
DESCRIPTION
Refer to DTCs C1401 and C1402 (See page
).
DTC Code
|
DTC Detection Condition
|
Trouble Area
|
C1413
C1414
|
Any of the following is detected:
-
An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
-
At a vehicle speed 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
-
At a vehicle speed 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
|
-
Front speed sensor RH/LH
-
Speed sensor circuit
-
Speed sensor rotor
-
Skid control ECU (Brake actuator assembly)
|
HINT:
-
DTC C1413 is for the front speed sensor RH.
-
DTC C1414 is for the front speed sensor LH.
WIRING DIAGRAM
Refer to DTCs C1401 and C1402 (See page
).
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (See page
).
PROCEDURE
1.
|
CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
|
(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page
).
ABS/VSC/TRAC
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
FR Speed Sensor Voltage Open
|
Front speed sensor RH voltage open detection / Error or Normal
|
Error: Momentary interruption
Normal: Normal
|
-
|
FL Speed Sensor Voltage Open
|
Front speed sensor LH voltage open detection / Error or Normal
|
Error: Momentary interruption
Normal: Normal
|
-
|
OK:
Normal (There are no momentary interruptions.)
HINT:
Perform the above inspection before removing the sensor and connector.
OK
|
|
|
2.
|
READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
|
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Start the engine.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
(f) Select the Data List using the Techstream (See page
).
ABS/VSC/TRAC
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
FR Wheel Speed
|
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
|
Vehicle stopped: 0 km/h (0 mph)
|
When driving at constant speed: No large fluctuations
|
FL Wheel Speed
|
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
|
Vehicle stopped: 0 km/h (0 mph)
|
When driving at constant speed: No large fluctuations
|
(g) Check the speed value output from the speed sensor displayed on the Techstream.
HINT:
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page
).
OK:
The speed value output from the speed sensor displayed on the Techstream is the similar speed as indicated on the speedometer.
OK
|
|
|
(a) Turn the ignition switch off.
(b) Clear the DTCs (See page
).
(c) Turn the ignition switch off.
(d) Start the engine.
(e) Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
(f) Check if the same DTC is output (See page
).
Result
|
Proceed to
|
DTCs C1413 and C1414 are not output.
|
A
|
DTCs C1413 and/or C1414 are output.
|
B
|
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page
).
4.
|
CHECK FRONT SPEED SENSOR INSTALLATION
|
(a) Turn the ignition switch off.
|
|
(b) Check the speed sensor installation.
OK:
There is no clearance between the sensor and the front steering knuckle.
The installation bolt is tightened properly.
Torque
8.0 N*m (82 kgf*cm, 71 in.*lbf)
Text in Illustration
*a
|
OK
|
*b
|
NG
|
*c
|
Clearance
|
*d
|
8.0 N*m (82 kgf*cm, 71 in.*lbf)
|
OK
|
|
|
5.
|
CHECK FRONT SPEED SENSOR TIP
|
(a) Remove the front speed sensor (See page
).
(b) Check the speed sensor tip.
OK:
No scratches, oil, or foreign matter on the sensor tip.
HINT:
-
If the sensor is contaminated with oil or other foreign material, clean the sensor.
-
If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
NOTICE:
Check the speed sensor signal after cleaning or replacement (See page
).
NG |
|
CLEAN OR REPLACE FRONT SPEED SENSOR
|
OK
|
|
|
6.
|
CHECK FRONT SPEED SENSOR ROTOR
|
(a) Remove the front speed sensor rotor (See page
).
(b) Check the speed sensor rotor.
OK:
No scratches, oil, or foreign matter on the rotor.
NOTICE:
Check the speed sensor signal after cleaning or replacement (See page
).
HINT:
If the front speed sensor rotor needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
NG |
|
CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR
|
OK
|
|
|
7.
|
CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
|
(a) Install the front speed sensor and the front speed sensor rotor.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
(c) Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for RH
Tester Connection
|
Condition
|
Specified Condition
|
A75-31 (FR+) - A20-2 (FR+)
|
Always
|
Below 1 Ω
|
A75-31 (FR+) - Body ground
|
Always
|
10 kΩ or higher
|
A75-30 (FR-) - A20-1 (FR-)
|
Always
|
Below 1 Ω
|
A75-30 (FR-) - Body ground
|
Always
|
10 kΩ or higher
|
for LH
Tester Connection
|
Condition
|
Specified Condition
|
A75-18 (FL+) - A6-2 (FL+)
|
Always
|
Below 1 Ω
|
A75-18 (FL+) - Body ground
|
Always
|
10 kΩ or higher
|
A75-17 (FL-) - A6-1 (FL-)
|
Always
|
Below 1 Ω
|
A75-17 (FL-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
8.
|
INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
|
(a) Reconnect the skid control ECU (brake actuator assembly) connector.
|
|
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for RH
Tester Connection
|
Switch Condition
|
Specified Condition
|
A20-2 (FR+) - Body ground
|
Ignition switch ON
|
8 to 14 V
|
for LH
Tester Connection
|
Switch Condition
|
Specified Condition
|
A6-2 (FL+) - Body ground
|
Ignition switch ON
|
8 to 14 V
|
NOTICE:
Check the speed sensor signal after replacement (See page
).
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page
).
Text in Illustration
*a
|
Front view of wire harness connector
(to Front Speed Sensor)
|
|