| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM1000000018J4W |
| Model Year Start: 2018 | Model: Sienna | Prod Date Range: [11/2017 - ] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: DATA LIST / ACTIVE TEST; 2018 - 2020 MY Sienna [11/2017 - ] | ||
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Panoramic View Monitor / Data List.
(e) Read the Data List according to the display on the Techstream.
Panoramic View Monitor
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Destination Data Check |
Status of the Destination Data check |
OK/NG |
OK: Parking assist ECU is normal NG: Parking assist ECU is abnormal |
- |
|
Back Guide Monitor Type Check |
Status of the Back Guide Monitor Type Check |
OK/NG |
OK: Parking assist ECU is normal NG: Parking assist ECU is abnormal |
- |
|
Main CPU Forced Termination Detection Record |
A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the engine switch off and a forced end was applied |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Main CPU Abnormal Response Record |
A history item indicating that the main CPU became unresponsive in normal status |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Main CPU Abnormal Reset Record |
A history item indicating that the main CPU was reset, although the engine switch was not turned off in normal status |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Image Processing IC Written Protect Record |
A history item indicating that the image processing IC memory was write protected |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Image Processing IC Initialized Malfunction Record |
A history item indicating that the image processing IC memory was not initialized |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Main EEPROM Access Status |
Main EEPROM access status |
OK/NG |
OK: Parking assist ECU is normal NG: Parking assist ECU is abnormal |
- |
|
Sub EEPROM Access Status |
Sub-EEPROM access status |
OK/NG |
OK: Parking assist ECU is normal NG: Parking assist ECU is abnormal |
- |
|
System Power Supply Voltage Malfunction Record |
A history item indicating an abnormally generated-voltage value from the system power source |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Main CPU Starting Malfunction Record |
A history item indicating that the main CPU did not start |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
CAN CPU Boot Malfunction Record |
A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved |
Unrec/Rec |
Unrec: Parking assist ECU is normal Rec: Parking assist ECU is abnormal |
- |
|
Visual Display Line Status |
Displays the status of the video signals displayed on the radio and display receiver assembly* |
OK/NG |
OK: Parking assist ECU is normal NG: Parking assist ECU is abnormal |
Not applicable |
|
Wheel Speed Sensor (4wheel) |
Reception state of the vehicle speed signal from the skid control ECU (brake actuator assembly) |
Valid/Invalid |
Valid: Speed signal received Invalid: Speed signal not received |
- |
|
Continuous Bus Off |
Continuous Bus Off |
Not Detected/Detected |
Not Detected: Communication condition available Detected: Communication condition not available |
- |
|
Sending CAN Message |
Communication condition from parking assist ECU |
OK/NG |
OK: Communication condition available NG: Communication condition not available |
- |
|
Shift R Position |
Reverse signal |
OFF/ON |
OFF: Shift lever in any position except R ON: Shift lever in R |
- |
|
Camera Changing SW Signal Status |
Pattern select switch assembly status |
ON/OFF |
ON: Pattern select switch assembly pressed OFF: Pattern select switch assembly not pressed |
- |
|
Back Camera Availability Consistency |
Status of ECU stored in rear television camera assembly |
OK/NG |
OK: Normal NG: Front television camera assembly or parking assist ECU is abnormal |
- |
|
Side Camera LH Availability Consistency |
Status of ECU stored in side television camera assembly LH |
OK/NG |
OK: Normal NG: Side television camera assembly LH or parking assist ECU is abnormal |
- |
|
Front Camera Availability Consistency |
Status of ECU stored in front television camera assembly |
OK/NG |
OK: Normal NG: Front television camera assembly or parking assist ECU is abnormal |
- |
|
Side Camera RH Availability Consistency |
Status of ECU stored side television camera assembly RH |
OK/NG |
OK: Normal NG: Side television camera assembly RH or parking assist ECU is abnormal |
- |
|
Image Adjustment Status |
Status of the image adjustment status |
Incomplete/Processing/Complete |
Incomplete: Image adjustment incomplete Processing: Image adjustment processing Complete: Image adjustment complete |
- |
|
Number of DTC |
Number of DTCs (past and present) |
Min: 0, Max: 255 |
Changes according to the number of DTCs output |
- |
|
|