AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK; 2018 - 2020 MY Sienna [11/2017

Last Modified: 04-05-2023	6.11:8.1.0	Doc ID: RM1000000018F6L
Model Year Start: 2018	Model: Sienna	Prod Date Range: [11/2017 - ]
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK; 2018 - 2020 MY Sienna [11/2017 - ]

OPERATION CHECK

NOTICE:

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occurs:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.

1. STORAGE CHECK

HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode (See page ).

(b) Select "Failure Diagnosis" from the "Service Menu" screen.

(d) Storage Check

Result

(1) Select "DCU Storage Check" to start the radio and display receiver assembly storage check.

(2) Check the result displayed when the radio and display receiver assembly storage check is complete.

Screen Description

Display (Result)	Description
Checking	Check is in progress
OK	Radio and display receiver assembly storage is normal
NG	Radio and display receiver assembly storage is malfunctioning

HINT:

After selecting "DCU Storage Check", it may take a while for the result to be displayed.
If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the storage may not operate normally, and "NG" may be displayed. Make sure to perform troubleshooting with the cabin at an appropriate temperature.
If "NG" is displayed even when the cabin temperature is appropriate, replace the radio and display receiver assembly with a new one.

2. CHECK PANEL & STEERING SWITCH

HINT:

The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode ( ).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Panel & Steering Switch Check Mode

Screen Description

Display	Content
*a: Switch condition	"Pushed" is displayed when any switch is pushed.
*b: Number of switches pushed	Number of switches pushed at once is displayed. If 3 switches are pushed at once, "3" is displayed. If 4 or more switches are pushed at once, "More than 3" is displayed.
*c: Rotary switch direction	Direction of rotary switch is displayed.

(1) Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

Do not push any switch for 3 seconds or more as doing so may cancel diagnostic mode.

3. CHECK TOUCH SWITCH

HINT:

The touch switches on the screen are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode.

Click here

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Touch Switch Check

(1) Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:

A "+" mark is displayed where the display is touched.
The "+" mark remains on the display even after your finger is removed.

4. CHECK MICROPHONE

HINT:

The microphone and microphone input level are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode (See page ).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Microphone Check

Screen Description

Display	Content
*: w/ Voice Recognition Function
*a: Microphone input level meter	Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
b: Recording switch	Starts recording.
c: Stop switch	Stops recording and playing.
d: Play switch	Plays the recorded voice.

(1) When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.

(2) Push the recording switch and perform voice recording.

HINT:

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
While recording or playing, switches other than the stop switch cannot be pushed.
When no recording is present, the play switch cannot be pushed.
Recording will stop after 5 seconds or when the stop switch is pushed.

(3) Check that the recording indicator remains on while recording and that the recording can be played normally.

5. CHECK GPS (w/ Disc Player)

HINT:

GPS information is checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode.

Click here

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) GPS Check

*a: GPS

Display	Content
Reception number	Displays reception condition of the satellites used to determine vehicle position.	Blue: P (In use)	System is using GPS signal for location.
		Yellow: T (Receiving)	System is tracking GPS signal for location.
		No color: Not in use	System cannot receive GPS signal (searching for GPS signal).
Status	Displays reception status of the satellites used to determine vehicle position.	OK(3D)	3-dimensional location method is being used.
		OK(2D)	2-dimensional location method is being used.
		NG	Location data cannot be used.
		error	Reception error has occurred.
		-	Any other state.
Measurement ratio	Displays the ratio of satellites performing measurements.	3D	The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed.
		2D	The ratio of satellites performing 2D positioning is displayed.
		NG	The ratio of satellites not performing measurement is displayed.
Date	Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
Position	Latitude and longitude information on current position is displayed.

(1) When the "GPS Check" screen is displayed, check the values of each display.

HINT:

This screen is updated once per second.

(e) GPS Time Setting

Screen Description

Display	Content
*a: Time display	Displays the date and time in the device.
*b: Date and time setting screen	Setting is possible only when GPS signals are not being received.
*c: Cursor movement switch	Moves the cursor on the date and time setting screen to the right and left.
*d: Adjustment switch	Adjusts values of items selected by the cursor.
*e: OK switch	Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not being received).

(1) When GPS signals are not being received, the date and time in the device can be adjusted.

HINT:

Time setting is possible only when GPS signals are not being received. When the audio and visual system is receiving GPS signals, priority is given to displaying the time and date received via GPS.

6. CHECK VEHICLE SIGNAL

HINT:

Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode (See page ).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Vehicle Signal Check Mode

Screen Description

Display	Content
Battery	Battery voltage is displayed.
IG	Ignition switch ON/OFF state is displayed.
PKB	Parking brake ON/OFF state is displayed.
REV	Reverse signal ON/OFF state is displayed.
SPEED	Vehicle speed is displayed in km/h.
TAIL	Tail signal (light control switch) ON/OFF state is displayed.
ADIM/TCAN	Brightness state DIM (with)/BRIGHT (without) is displayed.

HINT:

Only items sending vehicle signals will be displayed.
This screen displays vehicle signals input to the radio and display receiver assembly.
This screen is updated once per second.

(1) When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

7. CHECK HANDS-FREE VOICE QUALITY SETTING

HINT:

The hands-free voice quality of a "Bluetooth" compatible phone can be adjusted using the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Enter diagnostic mode (See page ).

(b) Select "Function Check/Setting" from the "Service Menu" screen.

(d) Hands-Free Voice Quality Setting

*a	Numeric Keypad
*b	Setting Button
*c	Reset Button

(1) If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

(2) When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings

Parameter	Target Phenomenon	Voice Quality Type	Positive Effect of Changing Voice Quality	Negative Effect of Changing Voice Quality
A (Noise)	The other party hears background noise when listening to your voice.	1000	The amount of background noise the other party hears when listening to your voice is reduced.	The volume of voice the other party hears when listening to your voice may temporarily drop.
B (Noise)	The other party hears a lot of background noise when listening to your voice.	2000	The amount of background noise the other party hears when listening to your voice is sharply reduced.	The volume of voice the other party hears when listening to your voice may temporarily drop.
C (Echo)	The other party hears weak echoes.	0100	The amount of echo is reduced (low level).	Sound quality of the other party deteriorates (low level).
D (Echo)	The other party hears strong echoes.	0200	The amount of echo is reduced (high level).	Sound quality of the other party deteriorates (high level).

Settings (When Multiple Phenomenon Occurred)

Parameter	Target Phenomenon	Voice Quality Type	Positive Effect of Changing Voice Quality	Negative Effect of Changing Voice Quality
A+C	The other party hears background noise and weak echoes when listening to your voice.	1100	The amount of background noise the other party hears when listening to your voice is reduced. The amount of echo is reduced (low level).	The volume of voice may drop temporarily. Sound quality of the other party deteriorates (low level).
A+D	The other party hears background noise and strong echoes when listening to your voice.	1200	The amount of background noise the other party hears when listening to your voice is reduced. The amount of echo is reduced (high level).	The volume of voice may drop temporarily. Sound quality of the other party deteriorates (high level).
B+C	The other party hears a lot of background noise and weak echoes when listening to your voice.	2100	The amount of background noise the other party hears when listening to your voice is sharply reduced. The amount of echo is reduced (low level).	The volume of voice may drop temporarily. Sound quality of the other party deteriorates (low level).
B+D	The other party hears a lot of background noise and strong echoes when listening to your voice.	2200	The amount of background noise the other party hears when listening to your voice is sharply reduced. The amount of echo is reduced (high level).	The volume of voice may drop temporarily. Sound quality of the other party deteriorates (high level).

HINT:

The default value is "0000".
Settings will be applied when the setting button is selected.
If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by selecting "INIT".

8. CHECK SPEAKER

HINT:

This function is used when checking the speaker wiring and whether the speakers are functioning properly.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

(a) Turn audio mode on and play any audio source.

HINT:

This audio source will be used for the speaker check.

(b) Enter diagnostic mode (See page ).

(d) Select "System Check" from the "Failure Diagnosis" screen.

(e) Select "SPCheck ON" from the "System Check Mode" screen.

(f) Check the speaker wiring and check that the speakers are functioning properly.

HINT:

Check that each speaker outputs sound from the selected audio source properly.
"SP Check OFF" is displayed during the speaker check.
Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.
More than one speaker may sound simultaneously depending on the speaker wiring.

(g) Sound stops when any of the following conditions are met:

(1) The "SP Check OFF" switch is pressed.

(2) The ignition switch is turned off.

(3) Diagnostic mode is turned off.

(4) The screen is changed to another screen.

(5) Audio mode is turned off.

HINT:

This function is used to check the cause when the radio and display receiver assembly screen is blacked out.
Although the location where the malfunction was detected is displayed, the actual cause of the malfunction may be in another location.

9. CHECK SOFTWARE ERROR HISTORY

(a) Check Software Error History.

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

(5) When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

Software Error History Screen Description

Error Description	Trigger	Detail
Software Reset	Navi Microcomputer	Hexadecimal Number
	Audio Microcomputer
	CAN Microcomputer
No Video Signal	Front Monitor
No Video Signal	Rear Monitor
MOST Cold Restart	Always

HINT:

The trigger detects malfunctions and displays the location where the malfunction information was stored.
Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.
If an error that is unsupported by the Techstream occurs, a "-" is displayed for the display items.

(b) Clear software error history.

(1) When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page ).

Cleared using the Techstream.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.

10. CHECK OPTICAL DISC ERROR HISTORY

HINT:

This function is used to check the cause of an optical disc error.

(a) Check Optical Disc Error History.

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

(5) When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description

Display	Content
Error Type	Displays the type of error
Device	Displays the malfunctioning device
Date	Displays the date and time that the malfunction occurred

"Error Type" Screen Description

Error Type	Detection Condition	Action
Read Error	When a disc read error occurs	Proceed to next suspected area shown in Problem Symptoms Table (See page )
Disc damaged/upside down/dirty	When it is determined that any of the following is the cause of the disc read error: The disc cannot be read The disc cannot be read because of dirt or scratches The disc cannot be read because it is inserted upside down
Cannot determine disc type	An unsuitable disc is inserted
DPS error	When an error occurs while decoding MP3/WMA/AAC files
Some files are corrupt	When MP3/WMA/AAC files cannot be played back because they are unsupported Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read
Some files cannot be found	When a disc without music data is played back When there are no playable MP3/WMA/AAC files
Copy protection violation	When a file with copyright protection that cannot be played back is played back

"Device" Screen Description

Device	Component
DVD-P	Not available
CD-P	Radio and display receiver assembly
R-Seat DVD-P	Not available

HINT:

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.
If an error that is unsupported by the Techstream occurs, a "-" or blank is displayed for the display items.

(b) Clear optical disc error history.

(1) When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page ).

Cleared using the Techstream.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.

11. CHECK VIDEO DEVICE CONNECTION CHECK

HINT:

This function is used to detect disconnection of the video devices.
In order to inspect the RSE, a disc should be inserted into the radio and display receiver assembly.

(a) Check Video Device Connection Check.

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.

(5) When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

HINT:

DTCs are stored when errors are detected.
Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.

Video Device Connection Check Screen Description

Error Detected Image Line (Type)	Areas to be Checked
H/U - > Separate Display (GVIF)	Not available
H/U - > Full RSE (GVIF)	Not available
RSE - > Seat Back Display RH (GVIF)	Not available
RSE - > Seat Back Display LH (GVIF)	Not available
Rear Camera - > H/U (NTSC)	NTSC video signal between the radio and display receiver assembly and television camera assembly
IPA/BGM/PVM ECU - > Separate Display (GVIF)	Not available
IPA/BGM/PVM ECU - > H/U (NTSC)	Not available
IPA/BGM/PVM ECU - > H/U (GVIF)	Not available

(b) Clear video device connection check.

(1) When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well (See page ).

Cleared using the Techstream.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.

12. Valet Mode Cancel

HINT:

This function is used to cancel valet mode.

NOTICE:

When valet mode cannot be canceled, there is a possibility that the vehicle is stolen. Therefore, it is necessary to thoroughly check ownership of the vehicle.

(a) Cancel valet mode.

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Body Electrical / Navigation System / Utility / Valet Mode Cancel.

(5) Cancel valet mode.

13. CHECK "Bluetooth" CONNECTION HISTORY

HINT:

This function is used to check the connection history when the connection between the radio and display receiver assembly and a "Bluetooth" device is unstable.

(a) Check "Bluetooth" Connection History.

HINT:

"Bluetooth" Connection History displays data stored in the internal memory of the ECU, such as the date a "Bluetooth" connection was attempted and the progress of a "Bluetooth" connection.
By checking "Bluetooth" Connection History, the date, cause, etc. of a "Bluetooth" device failing to register or connect can be analyzed.
"Bluetooth" connection history indicates the estimated cause of a malfunction, but does not determine it. Therefore, checking "Bluetooth" Connection History may not improve the problem.
Performing inspection using the Techstream before recording the "Bluetooth" Connection History may clear the operation history.

(1) Connect the USB memory device to the No. 1 stereo jack adapter assembly.

(2) Enter diagnostic mode.

Click here

(3) Select "Failure Diagnosis" from the "Service Menu" screen.

(4) Select "Diagnosis Recorder" from the "Failure Diagnosis" screen.

(5) Push the "Recording ON/OFF" switch to enable "BT Communication Trace output" to be selected.

*a	Green Indicator

HINT:

When the green "Recording ON/OFF" indicator is illuminated, the "BT Communication Trace output" is grayed out and cannot be selected.

(6) Select "BT Communication Trace output" for 3 seconds.

(7) According to the instructions on the screen, save the "Bluetooth" Connection History data to a USB memory device.

(8) Select "Recording ON/OFF" on the Diagnosis Recorder screen to illuminate the green "Recording ON/OFF" indicator.

HINT:

Make sure that the green "Recording ON/OFF" indicator returns to illuminated state, after performing the above procedure.

(9) Connect the USB memory device with the saved "Bluetooth" Connection History data to the Techstream.

(10) Turn the Techstream on.

(11) Enter the following menus: Advanced Function / Bluetooth Connection History.

(12) According to the Techstream screen, select the saved "Bluetooth" Connection History file.

(13) When an item is stored for "Bluetooth" Connection History, record it before proceeding with troubleshooting.

"Bluetooth" Connection History Screen Description

Item	Content
Occurrence Start Date/ Time	Date and time of "Bluetooth" connection are displayed
Occurrence End Date/Time	Date and time of "Bluetooth" disconnection are displayed
History Type	Type of "Bluetooth" Connection History is displayed
Result	"Bluetooth" connection result is displayed
Contents	"Bluetooth" connection status is displayed
"Bluetooth" Address	"Bluetooth" device address is displayed
Continuance Time	The number of retries when "Bluetooth" connection was performed is displayed

History Type: ACC ON

Result	Contents	Detail	Areas to be Checked
-	-	Ignition switch on (ACC)	-

History Type: Registration

Result	Contents	Detail	Areas to be Checked
Success (HFP)	No Error	"Bluetooth" device was registered as a hands-free device properly	-
Success (AVP)	No Error	"Bluetooth" device was registered as a "Bluetooth" audio device properly	-
Failure	Time Out	"Bluetooth" connection could not be established properly.	Check that the "Bluetooth" device is in the cabin Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection Restart the "Bluetooth" device and operate it again
	Authentication Error	Wrong PIN code was input for PIN code verification	Perform "Bluetooth" device registration again (Input PIN code correctly)
		Confirmation button was not selected even though a passkey was displayed.	Perform "Bluetooth" device registration again (When a passkey is displayed, select the confirmation button)
		A verification error occurred between the radio and display receiver assembly and "Bluetooth" device	Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again
	ACL Link Disconnection	"Bluetooth" connection was disconnected by operating the "Bluetooth" device	Perform "Bluetooth" device registration again
		"Bluetooth" connection could not be established due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" device registration again
		"Bluetooth" device was outside the communication area	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" device registration again
		"Bluetooth" setting on the "Bluetooth" device was off	Change the "Bluetooth" setting to on and perform "Bluetooth" device registration again
		"Bluetooth" device was off	Turn the "Bluetooth" device on and perform "Bluetooth" device registration again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again
	Memory Write Failure	"Bluetooth" device information could not be stored in the radio and display receiver assembly	Perform "Bluetooth" device registration again
	Other Error	An error other than above occurred	After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again
Cancel	No Error	Registration was suspended by operating the radio and display receiver assembly or "Bluetooth" device	-

History Type: Connection

Result	Contents	Detail	Areas to be Checked
Auto Connect Success (HFP) Manual Connect Success (HFP)	No Error	"Bluetooth" device was connected as a hands-free device properly	-
Auto Connect Failure (HFP) Manual Connect Failure (HFP)	Time Out	"Bluetooth" connection could not be established properly.	Check that the "Bluetooth" device is in the cabin Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection Restart the "Bluetooth" device and operate it again
	Authentication Error	Verification of authentication key between the radio and display receiver assembly and "Bluetooth" device failed	If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again
	Authentication Error	A verification error occurred between the radio and display receiver assembly and "Bluetooth" device	Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again
	Page Time Out	Could not find a "Bluetooth" device near the radio and display receiver assembly	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again
		"Bluetooth" connection could not be established due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" connection again
		"Bluetooth" device was outside the communication area	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again
		"Bluetooth" setting on the "Bluetooth" device was off	Change the "Bluetooth" setting to on and perform "Bluetooth" connection again
		"Bluetooth" device was off	Turn the "Bluetooth" device on and perform "Bluetooth" connection again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again

History Type: Connection

Result	Contents	Detail	Areas to be Checked
Auto Connect Failure (HFP) Manual Connect Failure (HFP)	ACL Link Disconnection	"Bluetooth" connection was disconnected by operating the "Bluetooth" device	Perform "Bluetooth" connection again
		"Bluetooth" connection could not be established due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" connection again
		"Bluetooth" device was outside the communication area	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again
		"Bluetooth" setting on the "Bluetooth" device was off	Change the "Bluetooth" setting to on and perform "Bluetooth" connection again
		"Bluetooth" device was off	Turn the "Bluetooth" device on and perform "Bluetooth" connection again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again
	SDP Error	HFP was disabled on the "Bluetooth" device	Enable HFP on the "Bluetooth" device and perform "Bluetooth" connection again
	SDP Error	"Bluetooth" device which operation had not been confirmed was used	Check that the "Bluetooth" device is hands-free compatible and its operation has been confirmed (See page )
	Other Error	An error other than above occurred	After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again
Manual Connect Cancel (HFP)	No Error	Connection was interrupted by operating the radio and display receiver assembly or "Bluetooth" device	-

History Type: Connection

Result	Contents	Detail	Areas to be Checked
Auto Connect Success (AVP) Manual Connect Success (AVP)	No Error	"Bluetooth" device was connected as a "Bluetooth" audio device properly	-
Auto Connect Failure (AVP) Manual Connect Failure (AVP)	Time Out	"Bluetooth" connection could not be established properly.	Check that the "Bluetooth" device is in the cabin Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection Restart the "Bluetooth" device and operate it again
	Authentication Error	Verification of authentication key between the radio and display receiver assembly and "Bluetooth" device failed	If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again
	Authentication Error	A verification error occurred between the radio and display receiver assembly and "Bluetooth" device	Restart the radio and display receiver assembly and "Bluetooth" device, and operate them again
	Page Time Out	Could not find a "Bluetooth" device near the radio and display receiver assembly	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again
		"Bluetooth" connection could not be established due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" connection again
		"Bluetooth" device was outside the communication area	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again
		"Bluetooth" setting on the "Bluetooth" device was off	Change the "Bluetooth" setting to on and perform "Bluetooth" connection again
		"Bluetooth" device was off	Turn the "Bluetooth" device on and perform "Bluetooth" connection again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again

History Type: Connection

Result	Contents	Detail	Areas to be Checked
Auto Connect Failure (AVP) Manual Connect Failure (AVP)	ACL Link Disconnection	"Bluetooth" connection was disconnected by operating the "Bluetooth" device	Perform "Bluetooth" connection again
		"Bluetooth" connection could not be established due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" connection again
		"Bluetooth" device was outside the communication area	Bring the "Bluetooth" device near the radio and display receiver assembly and perform "Bluetooth" connection again
		"Bluetooth" setting on the "Bluetooth" device was off	Change the "Bluetooth" setting to on and perform "Bluetooth" connection again
		"Bluetooth" device was off	Turn the "Bluetooth" device on and perform "Bluetooth" connection again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again
	SDP Error	AVP was disabled on the "Bluetooth" device	Enable AVP on the "Bluetooth" device and perform "Bluetooth" connection again
	SDP Error	"Bluetooth" device which operation had not been confirmed was used	Check that the "Bluetooth" device is "Bluetooth" audio compatible and its operation has been confirmed (See page )
	Other Error	An error other than above occurred	After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again
Manual Connect Cancel (AVP)	No Error	Connection was interrupted by operating the radio and display receiver assembly or "Bluetooth" device	-

History Type: Disconnection

Result	Contents	Detail	Areas to be Checked
Disconnection Complete (HFP)	Link Loss	The "Bluetooth" device was moved outside of the communication area	Move the "Bluetooth" device into the communication area
		"Bluetooth" connection was disconnected due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" connection again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again
	Disconnection from Partner	"Bluetooth" connection was disconnected by operating the "Bluetooth" device	-
	Disconnection from Self	"Bluetooth" connection was disconnected by operating the radio and display receiver assembly	-
	Other Error	An error other than above occurred	After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again
Disconnection Complete (AVP)	Link Loss	The "Bluetooth" device was moved outside of the communication area	Move the "Bluetooth" device into the communication area
		"Bluetooth" connection was disconnected due to wave interference around the vehicle	Check for wave interference and perform "Bluetooth" connection again
		A malfunction occurred in the "Bluetooth" device	Restart the "Bluetooth" device and operate it again
	Disconnection from Partner	"Bluetooth" connection was disconnected by operating the "Bluetooth" device	-
	Disconnection from Self	"Bluetooth" connection was disconnected by operating the radio and display receiver assembly	-
	Other Error	An error other than above occurred	After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again

History Type: Send

Result	Contents	Detail	Areas to be Checked
Success	No Error	Call was made properly	-
Failure	Out of Service	Outside the cellular phone service area	Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate the device again
	Redial Regulation	Redial of the "Bluetooth" device was restricted and could not make a hands-free call	Restart the "Bluetooth" device and operate it again
	Other Error	Could not make a hands-free call due to a "Bluetooth" device malfunction	Restart the "Bluetooth" device and operate it again
		Could not make a hands-free call due to a radio and display receiver assembly malfunction	After turning the ignition switch off and back to ON again, perform "Bluetooth" device registration again
		Could not make a hands-free call from the radio and display receiver assembly because the call status of the "Bluetooth" device was not transmitted to the radio and display receiver assembly	Restart the "Bluetooth" device and operate it again

(b) Clear "Bluetooth" connection history.

(1) When DTCs are cleared using any of the following operations, "Bluetooth" Connection History will be cleared as well (See page ).

Cleared using the Techstream.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.

14. Bluetooth Connection Sequence (Registration from onboard device)

15. Bluetooth Connection Sequence (Connection from onboard device after registration)

16. Bluetooth Connection Sequence (Registration from Bluetooth device)

17. Bluetooth Connection Sequence (Connection from Bluetooth device after registration)

18. Bluetooth Connection Sequence (Automatic Connection)

19. Bluetooth Connection Sequence (Manual Connection)

20. Bluetooth Connection Sequence (Disconnection Processing)

21. Bluetooth Connection Sequence (Phone Call Processing)

HINT:

Bluetooth Related Terms:

Marking in Repair Manual	Description
HFP	(Hands Free Profile)	Profile for making and receiving telephone calls.
AVP	(Audio/Video Profile)	Profile for music playback, lyric display and operation.
ACL	(Asynchronous Connection Less)	One of the Bluetooth connection methods used for data transfer.
SDP	(Service Discovery Protocol)	Protocol used to determine what kind of service is supported by the connected device.