Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018DN4
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 - 08/2018]
Title: NETWORKING: CAN COMMUNICATION SYSTEM: Central Gateway ECU Communication Stop Mode; 2018 MY Sienna [11/2017 - 08/2018]

Central Gateway ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Central Gateway ECU Communication Stop Mode

Communication system DTCs (DTCs that start with U) that correspond to "Central Gateway ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM

  • Central gateway ECU (network gateway ECU) CAN main wire or connector
  • Central gateway ECU (network gateway ECU) CAN branch wire or connector
  • Power source or inside of Central gateway ECU (network gateway ECU)
  • Central gateway ECU (network gateway ECU)
  • Central gateway ECU (network gateway ECU)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page 2018 - 2020 MY Sienna [11/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).
  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page 2017 - 2020 MY Sienna [08/2016 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION ).
  • Some parts must be initialized and set when replacing or removing and installing parts.

    Click here 2018 - 2020 MY Sienna [11/2017 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (See page 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM ).
  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) CAN MAIN OR BRANCH WIRE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the central gateway ECU (network gateway ECU) connector.

*A

Bus 2

*B

Bus 3

*C

Bus 5

*a

Front view of wire harness connector

(to Central Gateway ECU (Network Gateway ECU))

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Bus 2

Tester Connection

Condition

Specified Condition

D202-18 (CA4H) - D202-17 (CA4L)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω

Bus 3

Tester Connection

Condition

Specified Condition

D202-6 (CA3H) - D202-19 (CAYH)

Cable disconnected from negative (-) battery terminal

Below 1 Ω

D202-21 (CA3L) - D202-20 (CAYL)

Cable disconnected from negative (-) battery terminal

Below 1 Ω

Bus 5

Tester Connection

Condition

Specified Condition

D202-15 (CA5H) - D202-16 (CA5L)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

NG

REPAIR OR REPLACE CAN MAIN OR BRANCH WIRE CONNECTED TO CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (CA3H, CA3L, CA4H, CA4L, CA5H, CA5L, CAYH, CAYL)

OK

2.

CHECK HARNESS AND CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - POWER SOURCE)

(a) Disconnect the central gateway ECU (network gateway ECU) connector.

*a

Front view of wire harness connector

(to Central Gateway ECU (Network Gateway ECU))

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D202-10 (GND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

(c) Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page 2018 - 2020 MY Sienna [11/2017 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION )

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D202-1 (BATT) - Body ground

Always

11 to 14 V

D202-2 (ACC) - Body ground

Ignition switch ACC

11 to 14 V

D202-11 (IG1) - Body ground

Ignition switch ON

11 to 14 V

D202-12 (IG2) - Body ground

Ignition switch ON

11 to 14 V

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR