Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018DLR
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 -           ]
Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P032511,P033011; Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground; 2018 - 2020 MY Sienna [11/2017 -        ]

DTC

P032511

Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground

DTC

P033011

Knock Sensor 2 Bank 2 Circuit Short to Ground

DESCRIPTION

A flat-type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

The knock sensor is fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P032511

Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground

The knock sensor (bank 1) output voltage is less than 0.5 V for 1 second or more (1 trip detection logic).

  • Short in knock sensor (bank 1) circuit
  • Knock sensor (bank 1)
  • ECM

Comes on

DTC stored

  • SAE Code: P0327
  • DTC for Mexico Models: Applies

P033011

Knock Sensor 2 Bank 2 Circuit Short to Ground

The knock sensor (bank 2) output voltage is less than 0.5 V for 1 second or more (1 trip detection logic).

  • Short in knock sensor (bank 2) circuit
  • Knock sensor (bank 2)
  • ECM

Comes on

DTC stored

  • SAE Code: P0332
  • DTC for Mexico Models: Applies

HINT:

When DTC P032511 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.

Reference: Inspection using an oscilloscope

HINT:

The correct waveform is as shown.

ECM Terminal Name

Between KNK1 and EKNK

Between KNK2 and EKN2

Tester Range

1 V/DIV., 1 ms./DIV.

Condition

Engine speed maintained at 4000 rpm after warming up engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, and stores this DTC.

MONITOR STRATEGY

Related DTCs

P0327: Knock sensor (bank 1) range check (low voltage)

P0332: Knock sensor (bank 2) range check (low voltage)

Required Sensors/Components (Main)

Knock sensor

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

1 second

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

Both of the following conditions are met

-

Battery voltage

10.5 V or higher

Time after engine start

5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

Knock sensor voltage

Less than 0.5 V

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2017 - 2020 MY Sienna [08/2016 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2017 - 2020 MY Sienna [08/2016 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and wait 5 minutes [A].
  7. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  8. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  10. Input the DTC: P032511 or P033011.
  11. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.
    • [A] to [B]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

  • DTC P032511 is for the bank 1 knock sensor circuit.
  • DTC P033011 is for the bank 2 knock sensor circuit.
  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.
  • Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK SENSOR)

*a

Front view of wire harness connector

(to Knock Sensor)

*b

Bank 1

*c

Bank 2

(a) Disconnect the knock sensor connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

f3-2 - f3-1

Ignition switch ON

4.5 to 5.5 V

f5-2 - f5-1

Ignition switch ON

4.5 to 5.5 V

NG

GO TO STEP 3

OK

2.

INSPECT KNOCK SENSOR

(a) Inspect the knock sensor.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; 2GR-FKS (ENGINE CONTROL): KNOCK SENSOR: INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the knock sensor.

Click here 2018 - 2020 MY Sienna [11/2017 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

OK

GO TO STEP 4

NG

REPLACE KNOCK SENSOR

3.

CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)

(a) Disconnect the f3 and f5 knock sensor connectors.

(b) Disconnect the B67 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

f3-2 or B67-82 (KNK1) - Body ground

Always

10 kΩ or higher

f5-2 or B67-114 (KNK2) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK WHETHER DTC OUTPUT RECURS (DTC P032511 OR p033011)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

(e) Turn the ignition switch off and wait for at least 30 seconds.

(f) Turn the ignition switch to ON.

(g) Turn the Techstream on.

(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(i) Enter the following menus: Powertrain / Engine / Trouble Codes.

(j) Read the DTCs.

Result

Proceed to

DTCs are not output

A

DTC P032511 or P033011 is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM