Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM1000000018DLL
Model Year Start: 2018 Model: Sienna Prod Date Range: [11/2017 -           ]
Title: NETWORKING: CAN COMMUNICATION SYSTEM: Center Airbag Sensor Communication Stop Mode; 2018 - 2020 MY Sienna [11/2017 -        ]

Center Airbag Sensor Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Center Airbag Sensor Communication Stop Mode

Either condition is met:

  • Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the Techstream.

    Click here 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE 2019 - 2020 MY Sienna [08/2018 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE

  • Communication system DTCs (DTCs that start with U) that correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" are output.

    Click here 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DTC COMBINATION TABLE 2019 - 2020 MY Sienna [08/2018 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: DTC COMBINATION TABLE

  • Power source circuit of airbag sensor assembly
  • Airbag sensor assembly ground circuit
  • Airbag sensor assembly branch wire or connector
  • Airbag sensor assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here 2018 - 2020 MY Sienna [11/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here 2017 - 2020 MY Sienna [08/2016 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • Some parts must be initialized and set when replacing or removing and installing parts.

    Click here 2018 - 2020 MY Sienna [11/2017 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here 2018 MY Sienna [11/2017 - 08/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2019 - 2020 MY Sienna [08/2018 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK CAN BUS LINE FOR DISCONNECTION (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the airbag sensor assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D150-13 (CANH) - D150-22 (CANL)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω

Text in Illustration

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY
OK

2.

CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - POWER SOURCE)

(a) Disconnect the airbag sensor assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D150-25 (E1) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

D150-26 (E2) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

(c) Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page 2018 - 2020 MY Sienna [11/2017 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION )

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

D150-21 (IG2) - Body ground

Ignition switch ON

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)
OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR