| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM10000000105HG |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - ] |
| Title: UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT LEVER: REMOVAL; 2017 - 2020 MY Sienna [08/2016 - ] | ||
REMOVAL
PROCEDURE
1. REMOVE FRONT DOOR SCUFF PLATE RH
Click here
![2016 - 2017 MY Sienna [12/2015 - 11/2017]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
3. REMOVE COWL SIDE TRIM BOARD RH
Click here
4. REMOVE COWL SIDE TRIM BOARD LH
HINT:
Use the same procedure as for the RH side.
5. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Click here
6. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Use the same procedure as for the RH side.
7. REMOVE NO. 1 INSTRUMENT PANEL LOWER FINISH PANEL
Click here
8. REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY
Click here
9. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Click here
10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
11. REMOVE AIR CONDITIONING CONTROL ASSEMBLY
Click here
12. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
|
(a) Turn the shift lever knob sub-assembly counterclockwise to remove it from the shift lever assembly. |
|
13. REMOVE POSITION INDICATOR HOUSING ASSEMBLY
|
(a) Disengage the 4 clips to separate the position indicator housing assembly from the center instrument cluster finish panel sub-assembly. |
|
(b) Disconnect the indicator light wire connector to remove the position indicator housing assembly.
14. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
15. REMOVE CONSOLE BOX ASSEMBLY (for Slide Type)
Click here
16. REMOVE CONSOLE BOX ASSEMBLY (for Fixed Type)
Click here
17. REMOVE INSTRUMENT LOWER CENTER COVER (w/o Console Box)
Click here
18. REMOVE INSTRUMENT LOWER CENTER COVER (w/ Console Box)
Click here
19. REMOVE BOX BOTTOM MAT
Click here
20. REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY
Click here
21. REMOVE INSTRUMENT PANEL FINISH PANEL END RH
Click here
22. REMOVE INSTRUMENT PANEL FINISH PANEL END LH
HINT:
Use the same procedure as for the RH side.
23. REMOVE NO. 2 SWITCH HOLE BASE
Click here
24. REMOVE NO. 1 SWITCH HOLE BASE
Click here
25. REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY
Click here
26. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Click here
27. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD RETAINER
Click here
28. REMOVE SHIFT LEVER ASSEMBLY
(a) Move the shift lever to N.
|
(b) Disconnect the transmission control switch connector and shift lock control ECU connector. |
|
(c) Disengage the clamp to separate the wire harness from the shift lever assembly.
(d) Remove the 4 nuts and shift lever assembly from the instrument panel reinforcement.
29. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
|
(a) Disconnect the end of the transmission control cable assembly from the shift lever assembly. |
|
|
(b) Using a screwdriver, pull out the stopper of the transmission control cable assembly. NOTICE: Do not remove the stopper. If the stopper is removed, reinstall it to its original position. |
|
|
(c) Rotate the nut of the transmission control cable assembly counterclockwise approximately 270° and while holding the nut in that position, separate the cable outer of the transmission control cable assembly from the shift lever retainer. |
|
|
|