Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM10000000105HD |
Model Year Start: 2017 |
Model: Sienna |
Prod Date Range: [08/2016 -
] |
Title: UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT LEVER: INSTALLATION; 2017 - 2020 MY Sienna [08/2016 - ] |
INSTALLATION
PROCEDURE
1. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Check that the park/neutral position switch and shift lever are in N position.
(b) Rotate the nut of the transmission control cable assembly counterclockwise approximately 270° and while holding the nut in that position, press in the stopper until it makes 2 "click" sounds.
|
|
*1
|
Stopper
|
*2
|
Nut
|
*a
|
Turn
|
*b
|
Push
|
|
|
(c) Push the lock piece up from the back side of the adjuster case while pinching the claws on the lock piece.
|
|
*1
|
Adjuster Case
|
*2
|
Claw
|
*3
|
Lock Piece
|
|
|
(d) Install the cable outer of the transmission control cable assembly to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and press in the stopper.
HINT:
If the stopper cannot be pressed in, slightly rotate the nut clockwise and then press in the stopper.
|
|
(e) Connect the end of the transmission control cable assembly to the shift lever assembly.
NOTICE:
Check that the lock piece is pulled up.
|
|
2. INSTALL SHIFT LEVER ASSEMBLY
(a) Install the shift lever assembly to the instrument panel reinforcement with the 4 nuts.
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
(b) Engage the clamp to install the wire harness to the shift lever assembly.
(c) Connect the shift lock control ECU connector and transmission control switch connector.
(d) Press in and lock the lock piece to the adjuster case.
NOTICE:
-
Check that the park/neutral position switch and shift lever are in N position.
-
Securely press in the lock piece until the lock engages.
|
|
*1
|
Lock Piece
|
*2
|
Adjuster Case
|
*a
|
Press in
|
|
|
3. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD RETAINER
Click here
4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Click here
5. INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY
Click here
6. INSTALL NO. 1 SWITCH HOLE BASE
Click here
7. INSTALL NO. 2 SWITCH HOLE BASE
Click here
8. INSTALL INSTRUMENT PANEL FINISH PANEL END RH
Click here
9. INSTALL INSTRUMENT PANEL FINISH PANEL END LH
HINT:
Use the same procedure as for the RH side.
10. INSTALL INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY
Click here
11. INSTALL BOX BOTTOM MAT
Click here
12. INSTALL INSTRUMENT LOWER CENTER COVER (w/o Console Box)
Click here
13. INSTALL INSTRUMENT LOWER CENTER COVER (w/ Console Box)
Click here
14. INSTALL CONSOLE BOX ASSEMBLY (for Slide Type)
Click here
15. INSTALL CONSOLE BOX ASSEMBLY (for Fixed Type)
Click here
16. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
17. INSTALL POSITION INDICATOR HOUSING ASSEMBLY
(a) Connect the indicator light wire connector.
(b) Engage the 4 clips to install the position indicator housing assembly to the center instrument cluster finish panel sub-assembly.
18. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Turn the shift lever knob sub-assembly clockwise to install it to the shift lever assembly.
|
|
19. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
Click here
20. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
21. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Click here
22. INSTALL GLOVE COMPARTMENT DOOR SUB-ASSEMBLY
Click here
23. INSTALL NO. 1 INSTRUMENT PANEL LOWER FINISH PANEL
Click here
24. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Click here
25. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Use the same procedure as for the RH side.
26. INSTALL COWL SIDE TRIM BOARD RH
Click here
27. INSTALL COWL SIDE TRIM BOARD LH
HINT:
Use the same procedure as for the RH side.
28. INSTALL FRONT DOOR SCUFF PLATE RH
Click here
29. INSTALL FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
30. INSPECT SHIFT LEVER POSITION
Click here
|