- Air mix control servo motor (for front passenger side)
- Air conditioning harness
- Air conditioning amplifier
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM10000000102CD |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - ] |
| Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM: B1441/41; Air Mix Damper Control Servo Motor Circuit (Passenger Side); 2017 - 2020 MY Sienna [08/2016 - ] | ||
|
DTC |
B1441/41 |
Air Mix Damper Control Servo Motor Circuit (Passenger Side) |
DESCRIPTION
The air mix control servo motor sends pulse signals to indicate the damper position to the air conditioning amplifier. The air conditioning amplifier activates the motor (normal or reverse) based on these signals to move the air mix damper (front passenger side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the passenger side is controlled.
The air conditioning amplifier communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness.
HINT:
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or the damper is mechanically locked.
|
DTC Code |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B1441/41 |
Air mix damper position sensor value does not change even if air conditioning amplifier operates air mix control servo motor |
|
WIRING DIAGRAM
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Operate the front passenger side temperature adjustment switch.
(e) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(f) Check the value(s) by referring to the table below.
Air Conditioner
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Air Mix Servo Targ Pulse (P) |
Passenger side air mix servo motor target pulse / Min.: 128 Max.: 383 |
MAX. COLD: 233 (pulse) MAX. HOT: 135 (pulse) |
- |
OK:
The display is as specified in the Normal Condition column.
Result
|
Result |
Proceed to |
|---|---|
|
NG |
A |
|
OK (When troubleshooting according to Problem Symptoms Table) |
B |
|
OK (When troubleshooting according to the DTC) |
C |
| B |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| C |
|
|
|
2. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body / Air Conditioner / Active Test.
(e) Check the operation by referring to the table below.
Air Conditioner
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Air Mix Servo Targ Pulse (P) |
Air mix servo motor pulse (P side) |
Min.: 128, Max.: 383 |
- |
OK:
Air temperature changes in accordance with each control range.
| OK |
|
|
|
3. |
INSPECT AIR MIX CONTROL SERVO MOTOR |
(a) Replace the air mix control servo motor (See page
![2017 - 2020 MY Sienna [08/2016 - ]; HEATING / AIR CONDITIONING: FRONT AIR CONDITIONING UNIT: DISASSEMBLY](/t3Portal/stylegraphics/info.gif)
).
HINT:
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.
(b) Check for the DTC.
Result
|
Result |
Proceed to |
|---|---|
|
DTC B1441/41 is output |
A |
|
DTC B1441/41 is not output |
B |
| B |
|
|
|
4. |
INSPECT AIR CONDITIONING HARNESS |
(a) Replace the air conditioning harness (See page
).
HINT:
Since the air conditioning harness cannot be inspected while it is removed from the vehicle, replace the air conditioning harness with a new or a known good one and check that the condition returns to normal.
(b) Check for the DTC.
Result
|
Result |
Proceed to |
|---|---|
|
DTC B1441/41 is output |
A |
|
DTC B1441/41 is not output |
B |
| A |
|
| B |
|
|
|