Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM10000000101M5
Model Year Start: 2017 Model: Sienna Prod Date Range: [08/2016 - 11/2017]
Title: UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P08BA7F; Pressure Control Solenoid "L" Actuator Stuck Off; 2017 MY Sienna [08/2016 - 11/2017]

DTC

P08BA7F

Pressure Control Solenoid "L" Actuator Stuck Off

DESCRIPTION

Based on signals from the transmission revolution sensors (NT and NC), the actual gear is detected.

The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the shift solenoid valves, transmission valve body assembly and automatic transaxle assembly (clutch, brake, gear, etc.).

Actual gear when shift solenoid valve SL6 (without fail-safe control) malfunction occurs:

ECM commanded gear

1st

2nd

3rd

4th

5th

6th

7th

8th

*: Neutral

Actual gear during SL6 stuck ON malfunction

1st

N*

3rd

4th

5th

6th

7th

N*

Actual gear during SL6 stuck OFF malfunction

N*

2nd

3rd

4th

5th

6th

7th

8th

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P08BA7F

Pressure Control Solenoid "L" Actuator Stuck Off

1. Diagnosis Condition, 2. Malfunction Status, 3. Malfunction Time, 4. Other

SL6 stuck ON malfunction:

  1. Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the shift solenoid valves SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, electronic throttle or CAN2)
  2. When the ECM commands the transaxle to shift to 2nd or 8th gear, the engine overruns (neutral status).
  3. Malfunction status continues for 0.6 seconds or more
  4. 2-trip detection logic

SL6 stuck OFF malfunction:

  1. Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the shift solenoid valves SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, electronic throttle or CAN2)
  2. When the ECM commands the transaxle to shift to 1st gear, the engine overruns (neutral status).
  3. Malfunction status continues for 0.5 seconds or more
  4. 2-trip detection logic
  • Shift solenoid valve SLT
  • Shift solenoid valve SLU
  • Shift solenoid valve SL
  • Shift solenoid valve SL1
  • Shift solenoid valve SL2
  • Shift solenoid valve SL3
  • Shift solenoid valve SL4
  • Shift solenoid valve SL5
  • Shift solenoid valve SL6
  • Transmission valve body assembly
  • Torque converter assembly
  • Automatic transaxle assembly (clutch, brake, gear, etc.)

Comes on

DTC stored

SAE Code:

P08BB

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Related DTCs

P08BB:

Shift solenoid valve SL6/OFF malfunction

Shift solenoid valve SL6/ON malfunction

Required sensors/Components

Shift solenoid valve SL6

Frequency of operation

Continuous

Duration

0.5 sec.

MIL operation

2 driving cycles

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

All

The monitor will run whenever this DTC is not present.

(Not circuit malfunction)

P0717, P07BF, P07C0 (Turbine speed sensor circuit)

P0793, P07C5, P07C6 (Intermediate shaft speed sensor circuit)

P0962, P0963 (Shift solenoid valve SL1 circuit)

P0966, P0967 (Shift solenoid valve SL2 circuit)

P0970, P0971 (Shift solenoid valve SL3 circuit)

P2814, P2815 (Shift solenoid valve SL4 circuit)

P281D, P281E (Shift solenoid valve SL5 circuit)

P08C1, P08C2 (Shift solenoid valve SL6 circuit)

P2769, P2770 (Shift solenoid valve SL circuit)

P2764, P2763 (Shift solenoid valve SLU circuit)

P2720, P2721 (Shift solenoid valve SLT circuit)

P0117, P0118 (ECT sensor circuit)

P0335, P0337, P0338 (Crankshaft Position Sensor circuit)

P0712, P0713 (ATF temperature sensor circuit (TFT sensor))

P0327, P0328, P0332, P0333 (KCS sensor circuit)

P0121, P0122, P0123, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P061E, P0657, P0658, P2102, P2103, P2111, P2112, P2119, P2135 ((ETCS) Electronic throttle control system)

U0100 (CAN communication system)

NSW switch

"D" and "not R" and "not N"

Duration time from shifting "N" to "D"

4 sec. or more

ATF temperature

-10°C (14°F) or more

Engine

Starting

Fail-safe does not active due to following malfunctions:

-

Shift solenoid valve SL1

OFF or ON malfunction (P0746)

Shift solenoid valve SL2

OFF or ON malfunction (P0776)

Shift solenoid valve SL3

OFF or ON malfunction (P0796)

Shift solenoid valve SL4

OFF or ON malfunction (P2808)

Shift solenoid valve SL5

OFF or ON malfunction (P2817)

Shift solenoid valve SL6

OFF or ON malfunction (P08BB)

Shift solenoid valve SLT

OFF malfunction (P2714)

Shift solenoid valve SLU

ON malfunction (P2757)

Shift solenoid valve SL

ON malfunction (P0741)

All shift solenoids

Not being halted

Neutral command flag

Not met

OFF malfunction

ECM selected gear

3rd

First neutral state detection is fixed in 1st gear

-

Turbine speed - Output speed x (3rd gear ratio)

Less than 50 rpm

ON malfunction (A)

ECM selected gear

3rd

First neutral state detection is fixed in 2nd gear

-

Turbine speed - Output speed x (3rd gear ratio)

Less than 50 rpm

ON malfunction (B)

ECM selected gear

5th

First neutral state detection is fixed in 8th gear

-

Turbine speed - Output speed x (5th gear ratio)

Less than 50 rpm

ON malfunction (C)

Calculated load value

-

When A/C off

16% or more

When A/C on

19% or more

Throttle valve opening angle

3% or more

TYPICAL MALFUNCTION THRESHOLDS

OFF malfunction

  • When either conditions below is met: OFF malfunction (A) or (B)

    OFF malfunction (A)

    ECM selected gear

    3rd

    Turbine speed/Output speed (NT/NO)

    1.91 or more and 2.189 or less

    (When Output speed less than 350 rpm)

    Turbine speed - Output speed x 3rd gear ratio

    -50 rpm or more and 50 rpm or less

    (When Output speed 350 rpm or more)

    OFF malfunction (B)

    Shift solenoid valve SLT

    ON malfunction

    ECM selected gear

    1st

    1st gear pass detection

    Not fixed after transition to latest gear

ON malfunction

  • When one of the following conditions is met: ON malfunction (A), (B), (C) or (D)

    ON malfunction (A)

    ECM selected gear

    3rd

    Turbine speed/Output speed (NT/NO)

    1.91 or more and 2.189 or less

    (When Output speed less than 350 rpm)

    Turbine speed - Output speed x 3rd gear ratio

    -50 rpm or more and 50 rpm or less

    (When Output speed 350 rpm or more)

    ON malfunction (B)

    ECM selected gear

    5th

    (a) Turbine speed/Output speed (NT/NO)

    1.142 or more and 1.323 or less

    (When Output speed less than 550 rpm)

    Turbine speed - Output speed x 5th gear ratio

    -50 rpm or more and 50 rpm or less

    (When Output speed 550 rpm or more)

    ON malfunction (C)

    Shift solenoid valve SLT

    ON malfunction

    Following condition met

    a. or b.

    a. ECM selected gear

    2nd

    2nd gear pass detection

    Not fixed after transition to latest gear

    b. ECM selected gear

    8th

    8th gear pass detection

    Not fixed after transition to latest gear

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

HINT:

  • After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.

    Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Perform the D Position Shift Test inspection in Road Test. [*1]

    Click here 2017 MY Sienna [08/2016 - 11/2017]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: ROAD TEST

    HINT:

    [*1] : Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  8. Stop the vehicle.
  9. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
  10. Input the DTC: P08BA7F.
  11. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

NOTICE:

  • Perform the universal trip to clear permanent DTCs.

    Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: PRECAUTION

PROCEDURE

1.

CHECK DTC OUTPUT (IN ADDITION TO DTC P08BA7F)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Transmission / Trouble Codes.

(e) Read the DTCs using the Techstream.

Result

Proceed to

DTC P08BA7F and DTC P07407E, P07457F, P07757F, P07957F, P27137F, P28167F and/or P28077F are output

A

Only DTC P08BA7F is output

B

DTCs other than P07407E, P07457F, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are also output

C

HINT:

  • If any DTCs other than P07407E, P07457F, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are output, perform troubleshooting for those DTCs first.
  • If a shift solenoid valve is stuck ON or OFF, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.
B

GO TO STEP 3

C

GO TO DTC CHART

A

2.

CLEAR DTC AND PERFORM STALL SPEED TEST

(a) Clear the DTCs.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.

(b) Perform the stall speed test.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: MECHANICAL SYSTEM TESTS

Test Condition

Proceed to

Stall speed test can be performed

A

Stall speed test cannot be performed

B

B

GO TO STEP 5

A

3.

INSPECT SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 SL5 AND SL6

(a) Remove the shift solenoid valves SL1, SL2, SL3, SL4 SL5 and SL6.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): VALVE BODY ASSEMBLY: DISASSEMBLY

*a

Component without harness connected

(Shift Solenoid Valve SL1, SL2, SL3, SL4 SL5 and SL6)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve SL1 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL2 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL3 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL4 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL5 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

Shift solenoid valve SL5 connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

(c) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 SL5 OR SL6

OK

4.

INSPECT SHIFT SOLENOID VALVE SL

(a) Remove the shift solenoid valve SL.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): VALVE BODY ASSEMBLY: DISASSEMBLY

*1

Shift Solenoid Valve SL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve SL connector terminal - Shift solenoid valve SL body

20°C (68°F)

11 to 15 Ω

(c) Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE SL

OK

5.

INSPECT SHIFT SOLENOID VALVE SLT

(a) Remove the shift solenoid valve SLT.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): VALVE BODY ASSEMBLY: DISASSEMBLY

*a

Component without harness connected

(Shift Solenoid Valve SLT)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve SLT connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

(c) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

NG

REPLACE SHIFT SOLENOID VALVE SLT

OK

6.

INSPECT TRANSMISSION VALVE BODY ASSEMBLY

(a) Inspect the transmission valve body assembly.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): VALVE BODY ASSEMBLY: REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

OK

7.

INSPECT TORQUE CONVERTER ASSEMBLY

(a) Inspect the torque converter assembly.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): TORQUE CONVERTER AND DRIVE PLATE: INSPECTION

OK:

The torque converter assembly is normal.

NG

REPAIR OR REPLACE TORQUE CONVERTER ASSEMBLY

OK

8.

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

(a) Repair or replace the automatic transaxle assembly.

Click here 2017 - 2020 MY Sienna [08/2016 -        ]; UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE ASSEMBLY: COMPONENTS

NEXT

PERFORM A/T CODE REGISTRATION