Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000ZRIX
Model Year Start: 2017 Model: Sienna Prod Date Range: [08/2016 -           ]
Title: CRUISE CONTROL: CRUISE CONTROL SYSTEM: P050013,P05001F; Vehicle Speed Sensor "A" Circuit Open; 2017 - 2020 MY Sienna [08/2016 -        ]

DTC

P050013

Vehicle Speed Sensor "A" Circuit Open

DTC

P05001F

Vehicle Speed Sensor "A" Circuit Intermittent

DESCRIPTION

The cruise control system uses the same vehicle speed signal that is sent to the ECM for the SFI system. If DTC P050013 and P05001F are detected, perform the diagnosis using the inspection procedure for DTC P050013 and P05001F in the SFI system. The speed signal is converted for use by the cruise control inside the ECM. Both the SFI system and the cruise control system can set DTC P050013 and P05001F, however, the detection conditions of the two systems are different.

DTC No.

DTC Detection Condition

Trouble Area

P050013

The vehicle speed signal from the vehicle speed sensor is cut for 0.14 seconds or more while cruise control is in operation

  • Vehicle speed sensor
  • Vehicle speed sensor signal circuit
  • Combination meter assembly
  • ECM

P05001F

Momentary interruption and noise trouble codes are detected when a rapid change of vehicle speed occurs while the cruise control is in operation.

  • Vehicle speed sensor
  • Vehicle speed sensor signal circuit
  • Combination meter assembly
  • ECM

WIRING DIAGRAM

CAUTION / NOTICE / HINT

This DTC may be output by the vehicle stability control system at the same time. In that case, perform troubleshooting for the vehicle stability control system first.

PROCEDURE

1.

CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

(e) Check for DTCs.

Result

Result

Proceed to

DTC is not output

A

DTC is output

B

B

GO TO VEHICLE STABILITY CONTROL SYSTEM (DTC CHART)

(See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2018 - 2020 MY Sienna [11/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: DIAGNOSTIC TROUBLE CODE CHART )

A

2.

REPLACE COMBINATION METER ASSEMBLY

(a) Replace the combination meter assembly (See page 2016 - 2020 MY Sienna [12/2015 -        ]; METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL ).

NEXT

3.

CHECK DTC (CRUISE CONTROL SYSTEM)

(a) Clear the DTCs (See page 2016 - 2020 MY Sienna [12/2015 -        ]; CRUISE CONTROL: CRUISE CONTROL SYSTEM: DTC CHECK / CLEAR ).

(b) Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

(1) Drive the vehicle at a speed of 40 km/h (25 mph) or more.

(2) Turn the cruise control main switch on.

(3) Push the -SET switch to activate the cruise control.

(c) Check for DTCs (See page 2016 - 2020 MY Sienna [12/2015 -        ]; CRUISE CONTROL: CRUISE CONTROL SYSTEM: DTC CHECK / CLEAR ).

Result

Result

Proceed to

DTC is not output

A

DTC is output

B

A

END

B

REPLACE ECM