Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000ZMV8 |
Model Year Start: 2017 |
Model: Sienna |
Prod Date Range: [08/2016 -
] |
Title: THEFT DETERRENT / KEYLESS ENTRY: ENGINE IMMOBILISER SYSTEM(w/o Smart Key System): Engine does not Start because No Initial Combustion; 2017 - 2020 MY Sienna [08/2016 - ] |
Engine does not Start because No Initial Combustion
|
DESCRIPTION
-
When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.
-
If this symptom occurs, there may be a communication problem between the transponder key coil and the transponder key ECU assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the key and transponder key ECU assembly, refer to the Registration (See page
).
PROCEDURE
(a) Clear the DTCs (See page
).
NEXT
|
|
|
(a) Check for DTCs (See page
).
HINT:
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
Result
Result
|
Proceed to
|
No DTC output
|
A
|
DTC output
|
B
|
A
|
|
|
3.
|
READ VALUE USING TECHSTREAM (IMMOBILISER FUEL CUT)
|
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine / Data List.
Engine
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
Immobiliser Fuel Cut
|
Status of immobiliser fuel cut/
ON or OFF
|
-
|
-
|
OK:
The item in the Data List indicates "OFF".
Result
Result
|
Proceed to
|
NG
|
A
|
OK
|
B
|
A
|
|
|
4.
|
CHECK SECURITY INDICATOR LIGHT OPERATION
|
(a) When the key inserted in ignition key cylinder, check that the security indicator light off.
OK:
The security indicator light off.
NG
|
|
|
5.
|
CHECK SECURITY INDICATOR LIGHT OPERATION
|
(a) Perform inspection using a different key that has been registered to the vehicle.
(b) When the key inserted in ignition key cylinder, check that the security indicator light off.
OK:
The security indicator light off.
OK
|
|
|
6.
|
CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
|
(a) Perform inspection using a different key that has been registered to the vehicle.
(b) It leaves for 5 seconds by the ignition switch ON status, and the engine starting operation is done.
Result
Result
|
Proceed to
|
Engine cannot be started
|
A
|
Engine can be started
|
B
|
7.
|
REPLACE TRANSPONDER KEY COIL
|
(a) Replace the transponder key coil (See page
).
NEXT
|
|
|
8.
|
CHECK WHETHER ENGINE STARTS
|
(a) Using a registered key, turn the ignition switch to ON.
(b) Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
OK |
|
END (TRANSPONDER KEY COIL WAS DEFECTIVE)
|
NG
|
|
|
9.
|
REPLACE TRANSPONDER KEY ECU ASSEMBLY
|
(a) Replace the transponder key ECU assembly with a new one (See page
).
NOTICE:
Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Registration (See page
).
NEXT
|
|
|
10.
|
CHECK WHETHER ENGINE STARTS
|
(a) Using a registered key, turn the ignition switch to ON.
(b) Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
A |
|
END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)
|
B
|
|
|
(a) Replace the key.
NOTICE:
Key ID code registration is necessary when replacing the door control transmitter assembly, refer to Registration (See page
).
NEXT
|
|
|
12.
|
CHECK WHETHER ENGINE STARTS
|
(a) Using a registered key, turn the ignition switch to ON.
(b) Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
A |
|
END (KEY WAS DEFECTIVE)
|
|