Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000Z14X
Model Year Start: 2017 Model: Sienna Prod Date Range: [08/2016 - 11/2017]
Title: NETWORKING: CAN COMMUNICATION SYSTEM: Check CAN Bus Line for Short to GND; 2017 MY Sienna [08/2016 - 11/2017]

Check CAN Bus Line for Short to GND

DESCRIPTION

There may be a short circuit between the CAN bus line and GND when there is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.

Symptom

Trouble Area

There is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.

  • Short to GND
  • ECM
  • Airbag sensor assembly
  • Power management control ECU*1
  • Certification ECU (smart key ECU assembly)*1
  • Air conditioning amplifier assembly*2
  • Network gateway ECU*2
  • Main body ECU (multiplex network body ECU)
  • Combination meter assembly
  • 4WD ECU assembly*3*2
  • Yaw rate sensor*4
  • Brake actuator assembly (skid control ECU)
  • Steering angle sensor
  • Steering column assembly (power steering ECU)
  • Radio and display receiver assembly*5
  • Navigation receiver assembly*6
  • No. 1 junction connector
  • No. 2 junction connector
  • *1: w/ Smart Key System
  • *2: w/o Smart Key System
  • *3: for AWD
  • *4: w/ VDIM
  • *5: for Radio and Display Type
  • *6: for Navigation Receiver Type

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  • Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  • After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  • Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page 2017 - 2020 MY Sienna [08/2016 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION ).

NEXT

2.

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

(a) Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page 2017 MY Sienna [08/2016 - 11/2017]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION ).

NEXT

3.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)

(a) Disconnect the D180 No. 1 junction connector connector.

*a

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D16-6 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D16-14 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)

OK

4.

CONNECT CONNECTOR

(a) Reconnect the D180 No. 1 junction connector connector.

NEXT

5.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

(a) Disconnect the D179 No. 2 junction connector connector.

*a

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D16-6 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D16-14 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

NG

GO TO STEP 14

OK

6.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

HINT:

For vehicle without smart key system, go to step 7.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-3 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-14 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 23

OK

7.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

HINT:

For vehicle with smart key system, go to step 8.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-2 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-13 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 24

OK

8.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-1 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-12 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 25

OK

9.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

HINT:

Except radio and display type, go to step 10.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-6 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-17 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 26

OK

10.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

HINT:

Except navigation receiver type, go to step 11.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-6 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-17 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 27

OK

11.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

HINT:

For vehicle without smart key system, go to step 12.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-5 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-16 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 28

OK

12.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

HINT:

For vehicle with smart key system, go to step 13.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-5 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-16 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 29

OK

13.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-7 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-18 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

NG

GO TO STEP 30

14.

CONNECT CONNECTOR

(a) Reconnect the D179 No. 2 junction connector connector.

NEXT

15.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

(a) Disconnect the No. 1 junction connector connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-1 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-12 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

OK

16.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-2 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-13 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 31

OK

17.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING COLUMN ASSEMBLY (POWER STEERING ECU))

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-3 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-14 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 32

OK

18.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-4 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-15 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 33

OK

19.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - YAW RATE SENSOR)

HINT:

For vehicle without VDIM, go to step 20.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-8 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-19 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 34

OK

20.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-9 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-20 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 35

OK

21.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - 4WD ECU ASSEMBLY)

HINT:

Except AWD with smart key system, go to step 22.

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-5 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-16 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

NG

GO TO STEP 36

OK

22.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-7 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-18 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR

NG

GO TO STEP 37

23.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect the D88 certification ECU (smart key ECU assembly) connector.

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-3 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-14 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (CAN-H, CAN-L)

24.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(a) Disconnect the D75 air conditioning amplifier assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-2 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-13 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CAN-H, CAN-L)

25.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))

(a) Disconnect the A4 brake actuator assembly (skid control ECU) connector.

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-1 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-12 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE BRAKE ACTUATOR BRACKET ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (CAN-H, CAN-L)

26.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(a) Disconnect the D155 radio and display receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-6 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-17 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CAN-H, CAN-L)

27.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY)

(a) Disconnect the D153 navigation receiver assembly connector.

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-6 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-17 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CAN-H, CAN-L)

28.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)

(a) Disconnect the D89 power management control ECU connector.

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-5 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-16 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CAN-H, CAN-L)

29.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (NETWORK GATEWAY ECU)

(a) Disconnect the D90 network gateway ECU connector.

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-5 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-16 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE NETWORK GATEWAY ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CAN-H, CAN-L)

30.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

(a) Disconnect the D18 combination meter assembly connector.

*a

Rear view of wire harness connector

(to No. 2 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D179-7 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D179-18 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CAN-H, CAN-L)

31.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)

(a) Disconnect the D22 steering angle sensor connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-2 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-13 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

OK

REPLACE STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CAN-H, CAN-L)

32.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING COLUMN ASSEMBLY (POWER STEERING ECU))

(a) Disconnect the D35 steering column assembly (power steering ECU) connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-3 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-14 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE STEERING COLUMN ASSEMBLY (POWER STEERING ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING COLUMN ASSEMBLY (POWER STEERING ECU) (CAN-H, CAN-L)

33.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the D13 main body ECU (multiplex network body ECU) connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-4 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-15 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (CAN-H, CAN-L)

34.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR)

(a) Disconnect the L6 yaw rate sensor connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-8 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-19 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE YAW RATE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)

35.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)

(a) Disconnect the D150 airbag sensor assembly connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-9 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-20 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)

36.

CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD ECU ASSEMBLY)

(a) Disconnect the K1 4WD ECU assembly connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-5 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-16 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE 4WD ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD ECU ASSEMBLY (CAN-H, CAN-L)

37.

CHECK CAN BUS LINE FOR DISCONNECTION (ECM MAIN WIRE)

(a) Disconnect the A39 ECM connector.

*a

Rear view of wire harness connector

(to No. 1 Junction Connector)

*b

Front view of DLC3

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

D180-7 (CANH) - D16-4 (CG)

Ignition switch off

200 Ω or higher

D180-18 (CANL) - D16-4 (CG)

Ignition switch off

200 Ω or higher

OK

REPLACE ECM

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L)