Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000YZJH |
Model Year Start: 2017 |
Model: Sienna |
Prod Date Range: [08/2016 -
] |
Title: UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT LEVER: REMOVAL; 2017 - 2020 MY Sienna [08/2016 - ] |
REMOVAL
PROCEDURE
1. REMOVE FRONT DOOR SCUFF PLATE RH
Click here
2. REMOVE FRONT DOOR SCUFF PLATE LH
HINT:
Use the same procedure as for the RH side.
3. REMOVE COWL SIDE TRIM BOARD RH
Click here
4. REMOVE COWL SIDE TRIM BOARD LH
HINT:
Use the same procedure as for the RH side.
5. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Click here
6. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Use the same procedure as for the RH side.
7. REMOVE NO. 1 INSTRUMENT PANEL LOWER FINISH PANEL
Click here
8. REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY
Click here
9. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Click here
10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
11. REMOVE AIR CONDITIONING CONTROL ASSEMBLY
Click here
12. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Turn the shift lever knob sub-assembly counterclockwise to remove it from the shift lever assembly.
|
|
13. REMOVE POSITION INDICATOR HOUSING ASSEMBLY
(a) Disengage the 4 clips to separate the position indicator housing assembly from the center instrument cluster finish panel sub-assembly.
|
|
(b) Disconnect the indicator light wire connector to remove the position indicator housing assembly.
14. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
15. REMOVE CONSOLE BOX ASSEMBLY (for Slide Type)
Click here
16. REMOVE CONSOLE BOX ASSEMBLY (for Fixed Type)
Click here
17. REMOVE INSTRUMENT LOWER CENTER COVER (w/o Console Box)
Click here
18. REMOVE INSTRUMENT LOWER CENTER COVER (w/ Console Box)
Click here
19. REMOVE BOX BOTTOM MAT
Click here
20. REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY
Click here
21. REMOVE INSTRUMENT PANEL FINISH PANEL END RH
Click here
22. REMOVE INSTRUMENT PANEL FINISH PANEL END LH
HINT:
Use the same procedure as for the RH side.
23. REMOVE NO. 2 SWITCH HOLE BASE
Click here
24. REMOVE NO. 1 SWITCH HOLE BASE
Click here
25. REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY
Click here
26. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Click here
27. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD RETAINER
Click here
28. REMOVE SHIFT LEVER ASSEMBLY
(a) Move the shift lever to N.
(b) Disconnect the transmission control switch connector and shift lock control ECU connector.
|
|
*1
|
Transmission Control Switch Connector
|
*2
|
Shift Lock Control ECU Connector
|
|
|
(c) Disengage the clamp to separate the wire harness from the shift lever assembly.
(d) Remove the 4 nuts and shift lever assembly from the instrument panel reinforcement.
29. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Disconnect the end of the transmission control cable assembly from the shift lever assembly.
|
|
(b) Using a screwdriver, pull out the stopper of the transmission control cable assembly.
NOTICE:
Do not remove the stopper. If the stopper is removed, reinstall it to its original position.
|
|
(c) Rotate the nut of the transmission control cable assembly counterclockwise approximately 270° and while holding the nut in that position, separate the cable outer of the transmission control cable assembly from the shift lever retainer.
|
|
|