| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000YZJ5 |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - ] |
| Title: UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): DIFFERENTIAL OIL SEAL: REPLACEMENT; 2017 - 2020 MY Sienna [08/2016 - ] | ||
REPLACEMENT
PROCEDURE
1. REMOVE NO. 1 ENGINE UNDER COVER
Click here
![2017 - 2020 MY Sienna [08/2016 - ]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT FENDER APRON SEAL LH
Click here
3. DRAIN AUTOMATIC TRANSAXLE FLUID
|
(a) Remove the refill plug and gasket from the automatic transaxle case sub-assembly. |
|
|
(b) Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. |
|
|
(c) Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. |
|
(d) Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.
Torque:
1.7 N·m {17 kgf·cm, 15 in·lbf}
(e) Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.
HINT:
Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.
(f) Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.
HINT:
Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.
4. REMOVE FRONT DRIVE SHAFT ASSEMBLY
Click here
5. REMOVE DRIVE SHAFT BEARING BRACKET
Click here
6. REMOVE FRONT DRIVE SHAFT OIL SEAL LH
|
(a) Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly. SST: 09308-00010 NOTICE: Be careful not to damage the automatic transaxle case sub-assembly. |
|
7. REMOVE FRONT DRIVE SHAFT OIL SEAL RH
|
(a) Using SST, remove the front drive shaft oil seal RH from the transaxle housing. SST: 09308-00010 NOTICE: Be careful not to damage the transaxle housing. |
|
8. INSTALL FRONT DRIVE SHAFT OIL SEAL RH
|
(a) Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing. SST: 09316-60011 09316-00011 SST: 09950-70010 09951-07150 Standard Depth: -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) NOTICE:
|
|
9. INSTALL FRONT DRIVE SHAFT OIL SEAL LH
|
(a) Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly. SST: 09316-10010 SST: 09950-70010 09951-07100 Standard Depth: -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) NOTICE:
|
|
10. INSTALL DRIVE SHAFT BEARING BRACKET
Click here
11. INSTALL FRONT DRIVE SHAFT ASSEMBLY
Click here
12. ADJUST AUTOMATIC TRANSAXLE FLUID
Click here
13. INSPECT FOR FLUID LEAK
14. INSTALL FRONT FENDER APRON SEAL LH
Click here
15. INSTALL NO. 1 ENGINE UNDER COVER
Click here
|
|