Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000YW9M |
Model Year Start: 2017 |
Model: Sienna |
Prod Date Range: [08/2016 -
] |
Title: 2GR-FKS (ENGINE MECHANICAL): CYLINDER HEAD GASKET: REMOVAL; 2017 - 2020 MY Sienna [08/2016 - ] |
REMOVAL
PROCEDURE
1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Click here
2. REMOVE ENGINE HANGERS
Click here
3. REMOVE KNOCK SENSOR
Click here
4. REMOVE IGNITION COIL ASSEMBLY
Click here
5. REMOVE VACUUM PUMP ASSEMBLY
Click here
6. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
Click here
7. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Click here
8. REMOVE WATER PUMP PULLEY
Click here
9. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Click here
10. REMOVE NO. 5 CYLINDER BLOCK INSULATOR (w/ Oil Cooler)
Click here
11. REMOVE WIRE HARNESS CLAMP BRACKET
Click here
12. REMOVE CRANKSHAFT PULLEY
Click here
13. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
Click here
14. DISCONNECT WATER BY-PASS HOSE
Click here
15. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
Click here
16. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)
Click here
17. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)
Click here
18. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
Click here
19. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
Click here
20. REMOVE VVT SENSOR (for Intake Side of Bank 1)
Click here
21. REMOVE VVT SENSOR (for Exhaust Side of Bank 1)
Click here
22. REMOVE VVT SENSOR (for Intake Side of Bank 2)
Click here
23. REMOVE VVT SENSOR (for Exhaust Side of Bank 2)
Click here
24. REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR
Click here
25. REMOVE SENSOR WIRE
Click here
26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Click here
27. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Click here
28. REMOVE SPARK PLUG TUBE GASKET
Click here
29. REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)
Click here
30. REMOVE OIL COOLER PIPE (w/ Oil Cooler)
Click here
31. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Click here
32. REMOVE OIL STRAINER SUB-ASSEMBLY
Click here
33. REMOVE OIL PAN SUB-ASSEMBLY
(a) Remove the 16 bolts and 2 nuts from the oil pan sub-assembly.
NOTICE:
Make sure to clean the bolts and stud bolts and check the threads for cracks or other damage.
|
|
(b) Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and timing chain cover assembly or cylinder block sub-assembly with a screwdriver wrapped with protective tape.
NOTICE:
Be careful not to damage the contact surfaces of the cylinder block sub-assembly, timing chain cover assembly and oil pan sub-assembly.
|
|
(c) Remove the 2 oil pan gaskets from the timing chain cover assembly.
|
|
34. REMOVE TIMING CHAIN COVER ASSEMBLY
Click here
35. REMOVE TIMING CHAIN CASE OIL SEAL
Click here
36. SET NO. 1 CYLINDER TO TDC (COMPRESSION)
Click here
37. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Click here
38. REMOVE CHAIN TENSIONER SLIPPER
Click here
39. REMOVE CHAIN SUB-ASSEMBLY
Click here
40. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)
Click here
41. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Click here
42. REMOVE CAMSHAFT BEARING CAP (for Bank 1)
Click here
43. REMOVE CAMSHAFT
Click here
44. REMOVE NO. 2 CAMSHAFT
Click here
45. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
Click here
46. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)
Click here
47. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Click here
48. REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Click here
49. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
Click here
50. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
Click here
51. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
Click here
52. REMOVE SENSOR WIRE
Click here
53. REMOVE NO. 1 CHAIN VIBRATION DAMPER
Click here
54. REMOVE NO. 2 CHAIN VIBRATION DAMPER
Click here
55. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Click here
56. REMOVE VALVE LASH ADJUSTER ASSEMBLY
Click here
57. REMOVE VALVE STEM CAP
Click here
58. REMOVE WATER OUTLET
Click here
59. REMOVE CYLINDER HEAD SUB-ASSEMBLY
Click here
60. REMOVE CYLINDER HEAD GASKET
(a) Remove the cylinder head gasket from the cylinder block sub-assembly.
61. REMOVE CYLINDER HEAD LH
Click here
62. REMOVE NO. 2 CYLINDER HEAD GASKET
(a) Remove the No. 2 cylinder head gasket from the cylinder block sub-assembly.
63. INSPECT CYLINDER HEAD SET BOLT
Click here
|