- DTC judgment completed
- System normal
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000YSRH |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - ] |
| Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P059714; Thermostat Heater Control Circuit Short to Ground or Open; 2017 - 2020 MY Sienna [08/2016 - ] | ||
|
DTC |
P059714 |
Thermostat Heater Control Circuit Short to Ground or Open |
DESCRIPTION
Refer to DTC P059712.
Click here
![2017 - 2020 MY Sienna [08/2016 - ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P059712; Thermostat Heater Control Circuit Short to Battery+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P059714 |
Thermostat Heater Control Circuit Short to Ground or Open |
Open or short in thermostat heater circuit and power supply circuit (1 trip detection logic). |
|
Comes on |
DTC stored |
|
MONITOR DESCRIPTION
The ECM monitors the output voltage while the thermostat heater is operating.
The thermostat heater turns on and off according to ON/OFF switching of a transistor inside the ECM.
If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the thermostat heater circuit and stores a DTC.
MONITOR STRATEGY
|
Related DTCs |
P0598: Thermostat heater range check (low voltage) |
|
Required Sensors/Components (Main) |
Thermostat heater |
|
Required Sensors/Components (Related) |
- |
|
Frequency of Operation |
Continuous |
|
Duration |
3 seconds |
|
MIL Operation |
Immediate |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
None |
|
All of the following conditions are met |
- |
|
Either of the following conditions is met |
1 or 2 |
|
1. Both of the following conditions are met |
(a) and (b) |
|
(a) Last command to thermostat heater |
Off |
|
(b) Current command to thermostat heater |
Off |
|
2. Both of the following conditions are met |
(c) and (d) |
|
(c) Last command to thermostat heater |
On |
|
(d) Current command to thermostat heater |
On |
|
Battery voltage |
8 V or higher |
|
Starter |
Off |
|
Command to thermostat heater |
Off |
TYPICAL MALFUNCTION THRESHOLDS
|
Thermostat heater output terminal voltage level |
Low |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the Techstream on.
- Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
- Enter the following menus: Powertrain / Engine / Data List / Calculate Load and Coolant Temperature.
-
Drive the vehicle for at least 3 seconds at the Calculate Load of 45% or more and the Coolant Temperature of 90°C (194°F) or higher [B].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
- Stop the vehicle.
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P059714.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
-
[A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P059712.
Click here
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY |
(a) Inspect the water inlet with thermostat sub-assembly.
Click here
| NG |
|
|
|
2. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF WATER INLET WITH THERMOSTAT SUB-ASSEMBLY) |
|
*a |
Front view of wire harness connector (to Water Inlet with Thermostat Sub-assembly) |
(a) Disconnect the water inlet with thermostat sub-assembly connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
B63-1 (ETM+) - Body ground |
Ignition switch ON |
11 to 14 V |
| NG |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (WATER INLET WITH THERMOSTAT SUB-ASSEMBLY - ECM) |
(a) Disconnect the B63 water inlet with thermostat sub-assembly connector.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B63-2 (ETM-) - B67-64 (PTCR) |
Always |
Below 1 Ω |
|
B63-2 (ETM-) or B67-64 (PTCR) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P059714) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Start the engine.
(g) Turn the Techstream on.
(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine / Trouble Codes.
(j) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P059714 is output |
B |
| A |
|
| B |
|
|
5. |
CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - EFI MAIN RELAY) |
(a) Remove the EFI MAIN relay from the engine room relay block.
(b) Remove the EFI-MAIN No. 2 relay from the engine room relay block.
HINT:
Remove the EFI-MAIN NO. 2 relay connected between the checked terminals as the coil inside the relay influences the measurement value.
(c) Disconnect the B63 water inlet with thermostat sub-assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (EFI MAIN relay holder) - B63-1 (ETM+) |
Always |
Below 1 Ω |
|
3 (EFI MAIN relay holder) or B63-1 (ETM+) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
CHECK ECM POWER SOURCE CIRCUIT
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|