Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000YSQP |
Model Year Start: 2017 |
Model: Sienna |
Prod Date Range: [08/2016 -
] |
Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P070513,P070562; Transmission Range Sensor "A" Circuit Open; 2017 - 2020 MY Sienna [08/2016 - ] |
DTC
|
P070513
|
Transmission Range Sensor "A" Circuit Open
|
DTC
|
P070562
|
Transmission Range Sensor "A" Signal Compare Failure
|
DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P070513
|
Transmission Range Sensor "A" Circuit Open
|
All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic).
|
-
Open or short in park/neutral position switch circuit
-
Park/neutral position switch
-
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0705
-
DTC for Mexico Models: Applies
|
P070562
|
Transmission Range Sensor "A" Signal Compare Failure
|
Either of the following conditions A or B is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more:
(a) Any 2 or more of the following signals are on simultaneously:
-
P input signal
-
R input signal
-
D input signal
(b) Any 2 or more of the following signals are on simultaneously:
-
N input signal
-
R input signal
-
D input signal
(c) Any 2 or more of the following signals are on simultaneously:
-
NSW input signal
-
R input signal
-
D input signal
B. Any of the following conditions is met for 2 seconds or more with the shift lever in S:
-
NSW input signal is on
-
P input signal is on
-
N input signal is on
-
R input signal is on
|
-
Open or short in park/neutral position switch circuit
-
Park/neutral position switch
-
Open or short in transmission control switch circuit
-
Transmission control switch (shift lever assembly)
-
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0705
-
DTC for Mexico Models: Applies
|
MONITOR DESCRIPTION
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D, S. The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs
|
P0705: Transmission range switch verify switch input
|
Required Sensors/Components (Main)
|
Park/Neutral position switch
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
2 seconds: Case 1 and 3
60 seconds: Case 2
|
MIL Operation
|
2 driving cycles
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Case 1 and 2
Monitor runs whenever the following DTCs are not stored
|
None
|
All of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
Starter
|
Off
|
Case 3
Monitor runs whenever the following DTCs are not stored
|
None
|
All of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
Starter
|
Off
|
One of the following conditions is met
|
(a), (b), (c) or (d)
|
(a) Park position switch
|
On
|
(b) Neutral position switch
|
On
|
(c) Park/Neutral position switch
|
On
|
(d) R range position switch
|
On
|
TYPICAL MALFUNCTION THRESHOLDS
Case 1
Any two of the following conditions are met
|
1, 2 and 3
|
1. One of the following conditions is met
|
(a), (b) or (c)
|
(a) Park position switch
|
On
|
(b) Neutral position switch
|
On
|
(c) Park/Neutral position switch
|
On
|
2. R range position switch
|
On
|
3. D range position switch
|
On
|
Case 2
All of the following conditions are met
|
-
|
Park position switch
|
Off
|
Neutral position switch
|
Off
|
Park/Neutral position switch
|
Off
|
R range position switch
|
Off
|
D range position switch
|
Off
|
Case 3
S range position switch
|
On
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON and turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Turn the ignition switch to ON and turn the Techstream on [A].
-
Move the shift lever to R and wait 2 seconds or more [B].
-
Move the shift lever to N and wait 2 seconds or more [C].
-
Move the shift lever to D and wait 2 seconds or more [D].
-
Move the shift lever to S and wait 2 seconds or more [E].
-
Move the shift lever to P and wait 2 seconds or more [F].
-
Wait 1 minute or more [G].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [H].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P070513 or P070562.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine / Data List / Shift SW Status (P Range), Shift SW Status (R Range), Shift SW Status (N Range), Shift SW Status (S Range) and Shift SW Status (D Range).
(g) Read the values displayed on the Techstream.
Techstream Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
Shift SW Status (P Range)
|
Park/Neutral position switch status:
ON or OFF
|
-
ON: Shift lever in P
-
OFF: Shift lever not in P
|
-
|
Shift SW Status (R Range)
|
Park/Neutral position switch status:
ON or OFF
|
-
ON: Shift lever in R
-
OFF: Shift lever not in R
|
-
|
Shift SW Status (N Range)
|
Park/Neutral position switch status:
ON or OFF
|
-
ON: Shift lever in N
-
OFF: Shift lever not in N
|
-
|
Shift SW Status (S Range)
|
Transmission control switch status:
ON or OFF
|
-
ON: Shift lever in S
-
OFF: Shift lever not in S
|
-
|
Shift SW Status (D Range)
|
Park/Neutral position switch status:
ON or OFF
|
-
ON: Shift lever in D or S
-
OFF: Shift lever not in D or S
|
-
|
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM (NEUTRAL POSITION SW AND SHIFT SW STATUS)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Neutral Position SW and Shift SW Status (P, R, N and D Range).
(e) According to the display on the Techstream, read the Data List.
OK:
Techstream Display
|
Shift Lever Position
|
Specified Condition
|
Neutral Position SW
|
P or N
|
ON
|
Except P or N
|
OFF
|
Shift SW Status (P Range)
|
P
|
ON
|
Except P
|
OFF
|
Shift SW Status (R Range)
|
R
|
ON
|
Except R
|
OFF
|
Shift SW Status (N Range)
|
N
|
ON
|
Except N
|
OFF
|
Shift SW Status (D Range)
|
D or S
|
ON
|
Except D or S
|
OFF
|
OK
|
|
|
2.
|
READ VALUE USING TECHSTREAM (SHIFT SW STATUS (S RANGE))
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Shift SW Status (S Range).
(e) Read the Data List displayed on the Techstream.
OK:
Techstream Display
|
Shift Lever Position
|
Specified Condition
|
Shift SW Status (S Range)
|
S
|
ON
|
Except S
|
OFF
|
Result
|
Proceed to
|
OK
|
A
|
NG (for 2WD)
|
B
|
NG (for AWD)
|
C
|
B
|
|
|
3.
|
INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
|
(a) Inspect the transmission control switch.
Click here
OK
|
|
|
4.
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF TRANSMISSION CONTROL SWITCH)
|
*a
|
Front view of wire harness connector
(to Transmission Control Switch)
|
(a) Disconnect the transmission control switch connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
D41-6 (IG) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
|
(a) Disconnect the D41 control switch connector.
(b) Disconnect the A69 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D41-13 (S) - A69-17 (S)
|
Always
|
Below 1 Ω
|
D41-13 (S) or A69-17 (S) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
6.
|
INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
|
(a) Inspect the transmission control switch.
Click here
OK
|
|
|
7.
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF TRANSMISSION CONTROL SWITCH)
|
*a
|
Front view of wire harness connector
(to Transmission Control Switch)
|
(a) Disconnect the transmission control switch connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
D41-6 (IG) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
8.
|
CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
|
(a) Disconnect the D41 control switch connector.
(b) Disconnect the A69 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D41-13 (S) - A69-17 (S)
|
Always
|
Below 1 Ω
|
D41-13 (S) or A69-17 (S) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
9.
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH)
|
*a
|
Front view of wire harness connector
(to Park/Neutral Position Switch)
|
(a) Disconnect the park/neutral position switch connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
B66-1 (RB) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Result
|
Proceed to
|
OK (for 2WD)
|
A
|
OK (for AWD)
|
B
|
NG
|
C
|
C |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH POWER SOURCE CIRCUIT)
|
A
|
|
|
10.
|
INSPECT PARK/NEUTRAL POSITION SWITCH
|
(a) Inspect the park/neutral position switch.
Click here
OK
|
|
|
11.
|
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
|
(a) Disconnect the B66 park/neutral position switch connector.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
B66-4 (B) - B67-106 (NSW)
|
Always
|
Below 1 Ω
|
B66-7 (DL) - B67-139 (D)
|
Always
|
Below 1 Ω
|
B66-8 (NL) - B67-140 (N)
|
Always
|
Below 1 Ω
|
B66-2 (RL) - B67-107 (R)
|
Always
|
Below 1 Ω
|
B66-3 (PL) - B67-108 (P)
|
Always
|
Below 1 Ω
|
B66-4 (B) or B67-106 (NSW) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-7 (DL) or B67-139 (D) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-8 (NL) or B67-140 (N) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-2 (RL) or B67-107 (R) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-3 (PL) or B67-108 (P) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
12.
|
INSPECT PARK/NEUTRAL POSITION SWITCH
|
(a) Inspect the park/neutral position switch.
Click here
OK
|
|
|
13.
|
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
|
(a) Disconnect the B66 park/neutral position switch connector.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
B66-4 (B) - B67-106 (NSW)
|
Always
|
Below 1 Ω
|
B66-7 (DL) - B67-139 (D)
|
Always
|
Below 1 Ω
|
B66-8 (NL) - B67-140 (N)
|
Always
|
Below 1 Ω
|
B66-2 (RL) - B67-107 (R)
|
Always
|
Below 1 Ω
|
B66-3 (PL) - B67-108 (P)
|
Always
|
Below 1 Ω
|
B66-4 (B) or B67-106 (NSW) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-7 (DL) or B67-139 (D) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-8 (NL) or B67-140 (N) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-2 (RL) or B67-107 (R) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
B66-3 (PL) or B67-108 (P) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|