Last Modified: 04-05-2023 |
6.11:8.1.0 |
Doc ID: RM100000000YSQD |
Model Year Start: 2017 |
Model: Sienna |
Prod Date Range: [08/2016 -
] |
Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P060604,P060629,P06062A,P060647; Control Module Processor System Internal Failure; 2017 - 2020 MY Sienna [08/2016 - ] |
DTC
|
P060604
|
Control Module Processor System Internal Failure
|
DTC
|
P060629
|
Control Module Processor Signal Invalid
|
DTC
|
P06062A
|
Control Module Processor Signal Stuck in Range
|
DTC
|
P060647
|
Control Module Processor Watchdog/Safety MCU Failure
|
MONITOR DESCRIPTION
The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from these CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store a DTCs.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P060604
|
Control Module Processor System Internal Failure
|
ECM main CPU malfunction (1 trip detection logic)
|
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0606
-
DTC for Mexico Models: Applies
|
P060629
|
Control Module Processor Signal Invalid
|
ECM main CPU malfunction (1 trip detection logic)
|
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0606
-
DTC for Mexico Models: Applies
|
P06062A
|
Control Module Processor Signal Stuck in Range
|
ECM main CPU malfunction (2 trip detection logic)
|
ECM
|
Comes on
|
Comes on
|
-
SAE Code: P0606
-
DTC for Mexico Models: Applies
|
P060647
|
Control Module Processor Watchdog/Safety MCU Failure
|
ECM main CPU malfunction (1 trip detection logic)
|
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0606
-
DTC for Mexico Models: Applies
|
MONITOR STRATEGY
Related DTC
|
P0606: ECM/PCM processor performance
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
2 times
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
All
Monitor runs whenever the following DTCs are not stored
|
None
|
Case 1, Case 2 and Case 5
Both of the following conditions are met
|
-
|
Write Inhibit
|
Permit
|
Time after Write status forbiddance to permit
|
0.5 seconds or more
|
Case 3 and Case 4
All of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
Starter
|
Off
|
Write Inhibit
|
Permit
|
Time after Write status forbiddance to permit
|
0.5 seconds or more
|
TYPICAL MALFUNCTION THRESHOLDS
Case 1
One of the following conditions is met
|
5 seconds or more
|
ROM check sum
|
Error
|
RAM Read/Write check
|
Fail
|
Specific software routine operation period check
|
Fail
|
Software functional check
|
Fail
|
Case 2
Following condition is met
|
40 times or more
|
Specific software routine operation period check
|
Fail
|
Case 3
Following condition is met
|
25 times or more
|
DMA communication
|
No response
|
Case 4
Following condition is met
|
8 times or more
|
Watchdog from monitoring processor
|
Not toggle
|
CPU reset
|
Occurred
|
Case 5
One of the following conditions is met
|
(A) or (B)
|
(A)Following condition is met
|
More than 30 seconds
|
Specific software operation A validity check
|
Fail
|
(B)Following condition is met
|
More than 30 seconds
|
Specific software operation B validity check
|
Fail
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON and turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the Techstream off.
-
Turn the ignition switch off.
-
Disconnect the Techstream.
-
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
-
Connect the cable to the negative (-) battery terminal.
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON and turn the Techstream on.
-
Wait 1 second or more [A].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P060604, P060629 or P060647.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
CAUTION / NOTICE / HINT
NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
READ OUTPUT DTC (DTC P060604, P060629 OR P060647)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and turn the Techstream off.
(f) Disconnect the Techstream.
(g) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(h) Connect the cable to the negative (-) battery terminal.
(i) Connect the Techstream to the DLC3.
(j) Turn the ignition switch to ON.
(k) Turn the Techstream on.
(l) Wait 1 second or more.
(m) Enter the following menus: Powertrain / Engine / Trouble Codes.
(n) Read the DTCs.
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTC P060604, P060629 or P060647 is output
|
B
|
|