| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000YSQ7 |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - 11/2017] |
| Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P05042B; Brake Switch "A"/"B" Signal Cross Coupled; 2017 MY Sienna [08/2016 - 11/2017] | ||
|
DTC |
P05042B |
Brake Switch "A"/"B" Signal Cross Coupled |
DESCRIPTION
The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.
HINT:
The normal signal conditions are as shown in the table below.
|
Signal (ECM Terminal) |
Brake Pedal Released |
In Transition |
Brake Pedal Depressed |
|---|---|---|---|
|
STP |
OFF |
ON |
ON |
|
ST1- |
ON |
ON |
OFF |
- [OFF] denotes ground potential.
- [ON] denotes battery potential (+B).
On the Techstream, Data List item Stop Light SW is ON when the brake pedal is depressed.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P05042B |
Brake Switch "A"/"B" Signal Cross Coupled |
Conditions (a) and (b) are met for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b) STP signal OFF when ST1- signal OFF |
|
Does not come on |
DTC stored |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
-
Stop light switch assembly conditions can be checked using the Techstream.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.
-
Check the Data List indication when the brake pedal is depressed and released.
Brake Pedal Operation
Stop Light SW
Depressed
ON
Released
OFF
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK SPECIFICATIONS |
(a) Check the vehicle specifications.
|
Result |
Proceed to |
|---|---|
|
for Bulb Type Stop Light |
A |
|
for LED Type Stop Light |
B |
| B |
|
|
|
2. |
CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
|
*a |
Front view of wire harness connector (to Stop Light Switch Assembly) |
(a) Disconnect the stop light switch assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A58-2 - Body ground |
Always |
11 to 14 V |
|
A58-4 - Body ground |
Ignition switch ON |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY) |
|
|
3. |
INSPECT STOP LIGHT SWITCH ASSEMBLY |
(a) Inspect the stop light switch assembly (for Bulb Type Stop Light).
Click here
![2016 - 2020 MY Sienna [12/2015 - ]; LIGHTING (EXT): STOP LIGHT SWITCH: INSPECTION](/t3Portal/stylegraphics/info.gif)
| NG |
|
|
|
4. |
CHECK ECM (STP AND ST1 - VOLTAGE) |
(a) Disconnect the ECM connector.
|
*a |
Brake Pedal Depressed |
*b |
Brake Pedal Released |
|
*c |
Front view of wire harness connector (to ECM) |
- |
- |
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Brake Pedal Operation |
Specified Condition |
|---|---|---|
|
A69-42 (ST1-) - Body ground |
Released |
7.5 to 14 V |
|
Depressed |
0 to 1.5 V |
|
|
A69-27 (STP) - Body ground |
Released |
0 to 1.5 V |
|
Depressed |
7.5 to 14 V |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM) |
|
5. |
CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
|
*a |
Front view of wire harness connector (to Stop Light Switch Assembly) |
(a) Disconnect the stop light switch assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A59-1 (B) - Body ground |
Always |
11 to 14 V |
|
A59-5 (B) - Body ground |
Ignition switch ON |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY) |
|
|
6. |
INSPECT STOP LIGHT SWITCH ASSEMBLY |
(a) Inspect the stop light switch assembly (for LED Type Stop Light).
Click here
| NG |
|
|
|
7. |
CHECK ECM (STP AND ST1 - VOLTAGE) |
(a) Disconnect the ECM connector.
|
*a |
Brake Pedal Depressed |
*b |
Brake Pedal Released |
|
*c |
Front view of wire harness connector (to ECM) |
- |
- |
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Brake Pedal Operation |
Specified Condition |
|---|---|---|
|
A69-42 (ST1-) - Body ground |
Released |
7.5 to 14 V |
|
Depressed |
0 to 1.5 V |
|
|
A69-27 (STP) - Body ground |
Released |
0 to 1.5 V |
|
Depressed |
7.5 to 14 V |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM) |
|
|