- When ignition switch ON, total misfire count of all cylinders in last driving cycle is displayed.
- While engine is running, total misfire count of all cylinders in current driving cycle is displayed.
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000YSPU |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - 11/2017] |
| Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P030000,P030027,P030085-P030600; Random/Multiple Cylinder Misfire Detected; 2017 MY Sienna [08/2016 - 11/2017] | ||
|
DTC |
P030000 |
Random/Multiple Cylinder Misfire Detected |
|
DTC |
P030027 |
Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold |
|
DTC |
P030085 |
Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range |
|
DTC |
P030100 |
Cylinder 1 Misfire Detected |
|
DTC |
P030200 |
Cylinder 2 Misfire Detected |
|
DTC |
P030300 |
Cylinder 3 Misfire Detected |
|
DTC |
P030400 |
Cylinder 4 Misfire Detected |
|
DTC |
P030500 |
Cylinder 5 Misfire Detected |
|
DTC |
P030600 |
Cylinder 6 Misfire Detected |
DESCRIPTION
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P030000 |
Random/Multiple Cylinder Misfire Detected |
Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030027 |
Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold |
An emission deterioration misfire occurs (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P030085 |
Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range |
A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic). |
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030100 |
Cylinder 1 Misfire Detected |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030200 |
Cylinder 2 Misfire Detected |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030300 |
Cylinder 3 Misfire Detected |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030400 |
Cylinder 4 Misfire Detected |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030500 |
Cylinder 5 Misfire Detected |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
|
P030600 |
Cylinder 6 Misfire Detected |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
|
|
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
|
When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.
MONITOR DESCRIPTION
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
- Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 50 to 100 misfires per 1000 crankshaft revolutions) occurs once.
- An excessive number of misfires (approximately 50 to 100 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
Misfire Monitor for Mexico Models:
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
- Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 488 misfires per 1000 crankshaft revolutions) occurs once.
- An excessive number of misfires (approximately 488 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
- At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
- At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
MONITOR STRATEGY
|
Related DTCs |
P0300: Multiple cylinder misfire P0301: Cylinder 1 misfire P0302: Cylinder 2 misfire P0303: Cylinder 3 misfire P0304: Cylinder 4 misfire P0305: Cylinder 5 misfire P0306: Cylinder 6 misfire |
|
Required Sensors/Components (Main) |
Crankshaft position sensor VVT sensor |
|
Required Sensors/Components (Related) |
Engine coolant temperature Intake air temperature sensor (mass air flow meter) Mass air flow meter |
|
Frequency of Operation |
Continuous |
|
Duration |
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emission-related misfire) 200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire) |
|
MIL Operation |
2 driving cycles: Emission-related misfire MIL flashes immediate: Catalyst-damaging misfire |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Misfire
|
Monitor runs whenever the following DTCs are not stored |
P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0101, P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0117, P0118 (Engine coolant temperature sensor) P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328, P0332, P0333 (Knock sensor) P0335, P0337, P0338 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) |
|
Battery voltage |
8 V or higher |
|
VVT system |
Not operated by scan tool |
|
Engine speed |
400 to 6800 rpm |
|
Either of the following conditions is met |
(a) or (b) |
|
(a) Engine coolant temperature at engine start |
Higher than -7°C (19°F) |
|
(b) Engine coolant temperature |
Higher than 20°C (68°F) |
|
Fuel cut |
Off |
Monitor Period of Emission-related Misfire
|
First 1000 revolutions after engine start, or during check mode |
Crankshaft 1000 revolutions |
|
Except above |
Crankshaft 1000 revolutions x 4 |
Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
|
All of the following conditions 1, 2, 3 and 4 are met |
Crankshaft 200 revolutions x 3 |
|
Except above (MIL blinks immediately) |
Crankshaft 200 revolutions |
|
1. Driving cycles |
1st |
|
2. Check mode |
Off |
|
3. Engine speed |
Less than 2580 rpm |
|
4. Engine load |
Less than 50% |
Misfire for Mexico Models
|
Monitor runs whenever following DTCs are not present |
P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0101, P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0117, P0118 (Engine coolant temperature sensor) P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328, P0332, P0333 (Knock sensor) P0335, P0337, P0338 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) |
|
Battery voltage |
8 V or higher |
|
VVT system |
Not operated by scan tool |
|
Engine speed |
400 to 6800 rpm |
|
Either of the following conditions is met: |
(a) or (b) |
|
(a) Engine coolant temperature at engine start |
Higher than -7°C (19°F) |
|
(b) Engine coolant temperature |
Higher than 20°C (68°F) |
|
Fuel cut |
OFF |
Monitor Period of Emission-related Misfire for Mexico Models
|
First 1000 revolutions after engine start, or check mode |
Crankshaft 1000 revolutions |
|
Except above |
Crankshaft 1000 revolutions x 4 |
Monitor Period of Catalyst-damaging Misfire (MIL Blinks) for Mexico Models
|
All of the following conditions 1 and 2 are met: |
Crankshaft 200 revolutions |
|
1. Driving cycle |
1st |
|
2. Check mode |
OFF |
|
Except above (MIL blinks immediately) |
Crankshaft 200 revolutions x 3 |
TYPICAL MALFUNCTION THRESHOLDS
Monitor Period of Emission-related Misfire
|
Misfire rate |
2.0391% or higher |
Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
|
Number of misfires per 200 revolutions |
103 or more (varies with engine speed and engine load) |
Monitor Period of Emission-related Misfire for Mexico Models
|
Misfire rate |
16.6% or higher: for 1st 1000 revolutions 16.6% or higher: after 1st 1000 revolutions |
Monitor Period of Catalyst-damaging Misfire (MIL Blinks) for Mexico Models
|
Number of misfire per 200 revolutions |
103 or more (varies with intake air amount and engine speed) |
|
Paired cylinders misfire (MIL blinks immediately) |
Detected |
MONITOR RESULT
Refer to detailed information in Checking Monitor Status.
Click here
![2017 - 2020 MY Sienna [08/2016 - ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: CHECKING MONITOR STATUS](/t3Portal/stylegraphics/info.gif)
P0300: Misfire / EWMA MISFIRE
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A1 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of all cylinders in last ten driving cycles |
P0300: Misfire / MISFIRE RATE
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A1 |
$0C |
Multiply by 1 |
Count |
|
P0301: Misfire / EWMA MISFIRE1
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A2 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of cylinder 1 in last ten driving cycles |
P0301: Misfire / MISFIRE RATE1
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A2 |
$0C |
Multiply by 1 |
Count |
|
P0302: Misfire / EWMA MISFIRE2
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A3 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of cylinder 2 in last ten driving cycles |
P0302: Misfire / MISFIRE RATE2
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A3 |
$0C |
Multiply by 1 |
Count |
|
P0303: Misfire / EWMA MISFIRE3
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A4 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of cylinder 3 in last ten driving cycles |
P0303: Misfire / MISFIRE RATE3
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A4 |
$0C |
Multiply by 1 |
Count |
|
P0304: Misfire / EWMA MISFIRE4
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A5 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of cylinder 4 in last ten driving cycles |
P0304: Misfire / MISFIRE RATE4
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A5 |
$0C |
Multiply by 1 |
Count |
|
P0305: Misfire / EWMA MISFIRE5
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A6 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of cylinder 5 in last ten driving cycles |
P0305: Misfire / MISFIRE RATE5
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A6 |
$0C |
Multiply by 1 |
Count |
|
P0306: Misfire / EWMA MISFIRE6
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A7 |
$0B |
Multiply by 1 |
Count |
Total EWMA* misfire count of cylinder 6 in last ten driving cycles |
P0306: Misfire / MISFIRE RATE6
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$A7 |
$0C |
Multiply by 1 |
Count |
|
HINT:
*: EWMA (Exponential Weighted Moving Average) misfire counts for last 10 driving cycles (calculated) Calculation: 0.1 x (current counts) + 0.9 x (previous average)
Initial value for (previous average) = 0
CONFIRMATION DRIVING PATTERN
HINT:
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Permanent misfire and fuel system DTCs can only be cleared when performing the universal trip driving pattern when no malfunction is detected.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Record the DTC(s) and freeze frame data.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Using the Techstream, switch the ECM from normal mode to check mode.
Click here
- Start the engine.
- Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #6, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
-
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
HINT:
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
Engine speed
Duration
Idling
8.0 minutes or more
1000
4.5 minutes or more
2000
2.5 minutes or more
3000
1.5 minutes or more
-
Check whether misfires have occurred by checking DTCs and freeze frame data.
HINT:
Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
- Record the DTC(s), freeze frame data and misfire counts.
- Turn the ignition switch off and wait for at least 30 seconds.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
WIRING DIAGRAM
Refer to DTC P010012 for the mass air flow meter circuit.
Click here
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
-
Check the "Fuel Cut Elapsed Time" in the Data List or the Freeze Frame Data.
If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).
When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.
- By clearing the DTCs, "Fuel Cut Elapsed Time" will be cleared.
- If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
-
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
- There was insufficient fuel in the tank.
- Improper fuel was used.
- The spark plugs have been contaminated.
- The problem requires further diagnosis.
- After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #6).
- Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.
-
For 6 cylinder engine, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P030000 is set.
In the event of DTC P030000 being present, perform the following operations:
-
Clear the DTCs.
Click here
- Start the engine and conduct the confirmation driving pattern.
- Read the misfire count of each cylinder or DTC(s) using the Techstream.
- Repair the cylinder(s) that has a high misfiring count or is indicated by the DTC.
- After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P030000 is not set.
-
Clear the DTCs.
- When one of Short FT Bank 1, Long FT Bank 1, Short FT Bank 2 or Long FT Bank 2 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (20% or higher).
- When Coolant Temperature in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
- Vehicle body vibration caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
|
Result |
Proceed to |
|---|---|
|
DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output |
A |
|
DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 and other DTCs are output |
B |
HINT:
If any DTCs other than P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output, troubleshoot those DTCs first.
| B |
|
|
|
2. |
CHECK PCV HOSE CONNECTIONS |
(a) Check the PCV hose connections.
Click here
OK:
PCV valve and hose are correctly connected and are not damaged.
| NG |
|
REPAIR OR REPLACE PCV HOSE |
|
|
3. |
READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Misfire RPM and Misfire Load.
(e) Read and note the Misfire RPM and Misfire Load values.
HINT:
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
|
|
4. |
READ VALUE USING TECHSTREAM (CATALYST OT MISFIRE FUEL CUT) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Catalyst OT Misfire Fuel Cut.
(e) Read the value displayed on the Techstream.
|
Data List |
Result |
Proceed to |
|---|---|---|
|
Catalyst OT Misfire Fuel Cut |
Avail |
A |
|
Not Avl |
B |
| B |
|
|
|
5. |
PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT THE CATALYST OT MISFIRE PREVENT FUEL CUT) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test / Prohibit the Catalyst OT Misfire Prevent Fuel Cut.
(e) Perform the Active Test.
NOTICE:
When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.
|
|
6. |
CHECK MISFIRE COUNT OF PORT INJECTION |
(a) Start the engine and warm it up.
(b) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Port / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.
(c) Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 and Injection Mode displayed on the Techstream. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the Techstream [B].
|
Injection Mode |
Misfire Count |
Proceed to |
|---|---|---|
|
Port |
1 or 2 cylinders have misfire counts |
A |
|
3 cylinders or more have misfire counts |
||
|
There are no misfire counts |
B |
| B |
|
|
|
7. |
CHECK MISFIRE COUNT OF DIRECT INJECTION |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Start the engine and warm it up.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.
(f) Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 and Injection Mode displayed on the Techstream. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the Techstream [B].
|
Misfire Count |
Proceed to |
|
|---|---|---|
|
Port (Result of step 6) |
Direct |
|
|
1 or 2 cylinders have misfire counts |
1 or 2 cylinders have misfire counts |
A |
|
3 cylinders or more have misfire counts |
3 cylinders or more have misfire counts |
B |
|
1 or 2 cylinders have misfire counts |
There are no misfire counts |
C |
|
3 cylinders or more have misfire counts |
There are no misfire counts |
D |
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).
Click here
| A |
|
| B |
|
| C |
|
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION (MISFIRING CYLINDER)) |
|
|
8. |
CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE) |
(a) Check the fuel pressure (for low pressure side).
Click here
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).
Click here
| OK |
|
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION (MISFIRING CYLINDER)) |
|
|
9. |
CHECK FURL PUMP OPERATION (FOR LOW PRESSURE SIDE) |
(a) Check the fuel pump operation (for low pressure side).
Click here
| OK |
|
CHECK AND REPLACE FUEL SYSTEM |
| NG |
|
|
10. |
CHECK MISFIRE COUNT OF DIRECT INJECTION |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Start the engine and warm it up.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6.
(f) Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 and Injection Mode displayed on the Techstream. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the Techstream [B].
|
Misfire Count |
Proceed to |
|
|---|---|---|
|
Port (Result of step 6) |
Direct |
|
|
There are no misfire counts |
There are misfire counts |
A |
|
There are no misfire counts |
There are no misfire counts |
B |
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).
Click here
| A |
|
|
|
11. |
CHECK MISFIRE COUNT |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and turn the Techstream on.
(c) Clear the DTCs.
(d) Start the engine and warm it up.
(e) Enter the following menus: Powertrain / Engine / Data List / Injection Mode, Misfire Count Cylinder #1 to Misfire Count Cylinder #6, Misfire RPM and Misfire Load.
(f) Drive the vehicle with Misfire RPM and Misfire Load.
(g) Monitor all of the misfire count values or DTCs and Injection Mode displayed on the Techstream.
|
Misfire Count |
Injection Mode |
Proceed to |
|---|---|---|
|
There are no misfire counts |
- |
A |
|
1 or 2 cylinders have misfire counts |
Port or Either |
B |
|
3 cylinders or more have misfire counts |
Port or Either |
C |
|
There are misfire counts |
Direct |
D |
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).
Click here
| A |
|
| C |
|
| D |
|
|
|
12. |
INSPECT SPARK PLUG |
(a) Inspect the spark plug of the misfiring cylinder.
Click here
HINT:
Perform "Inspection After Repair" after replacing the spark plug.
Click here
| NG |
|
|
|
13. |
CHECK FOR SPARK (SPARK TEST) |
(a) Perform a spark test.
Click here
HINT:
- If the result of the spark test is normal, proceed to the next step.
-
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.
Click here
|
|
14. |
CHECK CYLINDER COMPRESSION PRESSURE |
(a) Measure the cylinder compression pressure of the misfiring cylinder.
Click here
HINT:
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click here
| OK |
|
| NG |
|
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION |
|
15. |
CHECK INTAKE SYSTEM |
(a) Check the intake system for vacuum leaks.
Click here
OK:
No leaks from the intake system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click here
| NG |
|
REPAIR OR REPLACE INTAKE SYSTEM |
|
|
16. |
READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
(e) Read the Data List twice, when the engine is both cold and warmed up.
Standard:
|
Techstream Display |
Condition |
Specified Condition |
|---|---|---|
|
Coolant Temperature |
Cold engine |
Same as ambient air temperature |
|
Warm engine |
Between 75 and 100°C (167 and 212°F) |
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here
| NG |
|
|
|
17. |
READ VALUE USING TECHSTREAM (MASS AIR FLOW SENSOR) |
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.
(e) Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.
(f) Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
Standard:
|
Techstream Display |
Condition |
Specified Condition |
|---|---|---|
|
Mass Air Flow Sensor |
Engine warmed up Shift lever position: P A/C: Off Engine Speed: 3000 rpm |
Between 10.6 gm/sec and 15.8 gm/sec |
| NG |
|
|
|
18. |
CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
(a) Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.
|
*a |
Timing Mark |
*b |
TDC Timing Mark |
|
*c |
Groove |
- |
- |
(b) Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.
(c) Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.
HINT:
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
OK:
Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.
HINT:
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
| OK |
|
|
|
19. |
CHECK ENGINE MECHANICAL SYSTEM |
(a) Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
| NG |
|
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA |
|
|
20. |
CONFIRM WHETHER DTC OUTPUT RECURS (MISFIRE DTCS) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
(j) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.
(k) Check the DTC judgment result.
|
Result |
Proceed to |
|---|---|
|
NORMAL (DTCs are not output) |
A |
|
ABNORMAL (DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output) |
B |
| A |
|
| B |
|
|
21. |
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION) |
(a) Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.
Click here
HINT:
Repair any problems.
|
|
22. |
CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
(j) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.
(k) Check the DTC judgment result.
|
Result |
Proceed to |
|---|---|
|
NORMAL (DTCs are not output) |
A |
|
ABNORMAL (DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output) |
B |
| A |
|
END |
|
|
23. |
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
(a) Disconnect the B56 mass air flow meter connector.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B56-3 (5V) - B67-90 (VC) |
Always |
Below 1 Ω |
|
B56-1 (FG) - B67-116 (VG) |
Always |
Below 1 Ω |
|
B56-2 (E2G) - B67-115 (E2G) |
Always |
Below 1 Ω |
|
B56-3 (5V) or B67-90 (VC) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B56-1 (FG) or B67-116 (VG) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B56-2 (E2G) or B67-115 (E2G) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
24. |
REPLACE MASS AIR FLOW METER |
(a) Replace the mass air flow meter.
Click here
HINT:
- If the results of the inspections performed in step 17 indicated no problem, proceed to the next step without replacing the mass air flow meter.
-
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click here
|
|
25. |
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON.
(g) Turn the Techstream on.
(h) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
(j) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.
(k) Check the DTC judgment result.
|
Result |
Proceed to |
|---|---|
|
NORMAL (DTCs are not output) |
A |
|
ABNORMAL (DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output) |
B |
| A |
|
END |
| B |
|
|
|