- DTC judgment completed
- System normal
| Last Modified: 04-05-2023 | 6.11:8.1.0 | Doc ID: RM100000000YIZD |
| Model Year Start: 2017 | Model: Sienna | Prod Date Range: [08/2016 - ] |
| Title: UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P275612,P275614; Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery; 2017 - 2020 MY Sienna [08/2016 - ] | ||
|
DTC |
P275612 |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery |
|
DTC |
P275614 |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open |
DESCRIPTION
The ECM controls the shift solenoid valve SLU using a predetermined current, and performs lock-up and flex lock-up control.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P275612 |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery |
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
|
|
Comes on |
DTC stored |
SAE Code: P2763 |
|
P275614 |
Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open |
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
|
|
Comes on |
DTC stored |
SAE Code: P2764 |
MONITOR DESCRIPTION
When an open or short to +B and ground in the shift solenoid valve SLU circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.
MONITOR STRATEGY
|
Related DTCs |
P2764: Shift solenoid valve SLU/Range check (Low current) P2763: Shift solenoid valve SLU/Range check (High current) |
|
Required sensors/Components |
Shift solenoid valve SLU |
|
Frequency of operation |
Continuous |
|
Duration |
P2763, P2764: 1 sec. |
|
MIL operation |
Immediate |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
All
|
Solenoid current cut status |
Not cut |
|
Battery voltage |
8 V or more |
|
Ignition Switch |
ON |
|
Starter |
OFF |
P2764
|
The monitor will run whenever the following DTCs are not present |
None |
|
Battery voltage |
10.5 V or more |
|
Target current |
0.2 A or more |
P2763
|
The monitor will run whenever the following DTCs are not present |
None |
|
Battery voltage |
10.5 V or more |
|
Following condition is met: |
Condition a. or b. |
|
a. Battery voltage |
8 V or more and less than 12.499 V |
|
Target current |
0.8 A or less |
|
b. Battery voltage |
12.5 V or more and less than 16 V |
|
Target current |
1 A or less |
TYPICAL MALFUNCTION THRESHOLDS
P2764
|
Solenoid current |
Less than 0.075 A |
P2763
|
Solenoid current |
a. or b. |
|
a. Battery voltage |
8 V or more and less than 12.499 V |
|
Target current |
More than 0.92 A |
|
b. Battery voltage |
12.5 V or more and less than 16 V |
|
Target current |
More than 1.1 A |
COMPONENT OPERATING RANGE
|
P2764: Solenoid current |
0.075 A or more |
|
P2763: Solenoid current |
a. or b. |
|
a. Battery voltage |
8 V or more and less than 12.499 V |
|
Target current |
0.92 A or less |
|
b. Battery voltage |
12.5 V or more and less than 16 V |
|
Target current |
1.1 A or less |
CONFIRMATION DRIVING PATTERN
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
-
When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
![2017 - 2020 MY Sienna [08/2016 - ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the Techstream on.
- Start the engine.
-
Perform the Lock-up Function inspection in Road Test. [*1]
Click here
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Stop the vehicle.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P275612 or P275614.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Perform the universal trip to clear permanent DTCs.
Click here
-
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click here
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU) - ECM) |
(a) Disconnect the B67 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B67-76 (SLU+) - B67-61 (SLU-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
B67-76 (SLU+) or B67-61 (SLU-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
|
|
2. |
REPLACE ECM |
(a) Replace the ECM.
Click here
| NEXT |
|
|
3. |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
(a) Disconnect the B65 transmission wire connector.
(b) Disconnect the B67 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B65-5 (SLU+) - B67-76 (SLU+) |
Always |
Below 1 Ω |
|
B65-4 (SLU-) - B67-61 (SLU-) |
Always |
Below 1 Ω |
|
B65-5 (SLU+) or B67-76 (SLU+) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
B65-4 (SLU-) or B67-61 (SLU-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM) |
|
|
4. |
INSPECT SHIFT SOLENOID VALVE SLU |
|
(a) Remove the shift solenoid valve SLU. Click here
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Shift solenoid valve SLU connector terminal 1 - terminal 2 |
20°C (68°F) |
5.0 to 5.6 Ω |
(c) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
OK:
Valve moves and makes operating sound.
| OK |
|
| NG |
|
|
|