Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VK8B
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 11/2017]
Title: DOOR / HATCH: HOOD LOCK CONTROL CABLE ASSEMBLY: INSTALLATION; 2016 - 2017 MY Sienna [12/2015 - 11/2017]

INSTALLATION

PROCEDURE

1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

(a) Pass the hood lock control cable into the engine compartment.

(b) Pass the cable rear side through the grommet until the cable stopper is attached to the grommet.

(c) Pass the cable front side through the upper radiator support.

(d) Engage the cable to the clamps.

(e) Connect the hood lock control cable to hood lock control lever.

2. INSTALL NO. 1 INSTRUMENT PANEL LOWER FINISH PANEL

2016 - 2017 MY Sienna [12/2015 - 11/2017]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: INSTALLATION+

3. INSTALL COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: INSTALLATION+ ).

4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

5. INSTALL DOOR SCUFF PLATE ASSEMBLY LH

HINT:

Use the same procedure as for the RH side (See page 2016 - 2017 MY Sienna [12/2015 - 11/2017]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: INSTALLATION+ ).

6. INSTALL HOOD LOCK ASSEMBLY

(a) Apply MP grease to the sliding areas of the lock.

(b) Connect the hood lock control cable.

(c) Install the A bolts and hood lock.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(d) Install the 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(e) Connect the connector.

7. INSPECT HOOD LOCK ASSEMBLY

2016 - 2020 MY Sienna [12/2015 -        ]; DOOR / HATCH: HOOD: ON-VEHICLE INSPECTION+

8. ADJUST HOOD LOCK ASSEMBLY

2016 - 2017 MY Sienna [12/2015 - 11/2017]; DOOR / HATCH: HOOD: ADJUSTMENT+

9. INSTALL HOOD LOCK NUT CAP

(a) Install a new hood lock nut cap.

10. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

2016 - 2017 MY Sienna [12/2015 - 11/2017]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: INSTALLATION+

11. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

2016 - 2017 MY Sienna [12/2015 - 11/2017]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: ADJUSTMENT+

12. INSTALL RADIATOR GRILLE SUB-ASSEMBLY

2016 - 2017 MY Sienna [12/2015 - 11/2017]; EXTERIOR PANELS / TRIM: FRONT BUMPER: INSTALLATION+

13. INSTALL FRONT FENDER LINER LH

(a) Install the 2 screws.

(b) Install the 2 clips.

(c) Install the pin hold clip.

NOTICE:

Install the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it.

After installation, confirm that the slot is vertical.

14. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

(a) Install the front wheel opening extension pad LH withe the 4 screws.

Torque:

7.0 N·m {71 kgf·cm, 62 in·lbf}

for screw A