Last Modified: 08-28-2024 6.11:8.1.0 Doc ID: RM100000000VK6Y
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR(for Rear Door): INSPECTION; 2016 - 2020 MY Sienna [12/2015 -        ]

INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

(a) Apply positive (+) battery voltage to connector terminal 2 (B).

Text in Illustration

*1

Motor Gear

*a

Component without harness connected

(Power Window Regulator Motor Assembly LH)

*b

Clockwise

*c

Counterclockwise

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

(b) Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.

Motor gear rotates clockwise
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.

Motor gear rotates counterclockwise
  • If the result is not as specified, replace the power window regulator motor assembly LH.

CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator onto the door.

2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

(a) Apply positive (+) battery voltage to connector terminal 2 (B).

Text in Illustration

*1

Motor Gear

*a

Component without harness connected

(Power Window Regulator Motor Assembly RH)

*b

Clockwise

*c

Counterclockwise

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

(b) Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.

Motor gear rotates counterclockwise
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.

Motor gear rotates clockwise
  • If the result is not as specified, replace the power window regulator motor assembly RH.

CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator onto the door.