Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VK6A
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH; 2016 - 2020 MY Sienna [12/2015 -        ]

Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

DESCRIPTION

If the manual up/down function can be performed but the auto up/down function cannot, the fail-safe mode may be functioning.

If the power window initialization (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION ) has not been performed, the auto up/down function will not operate.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • If the rear power window regulator motor assembly RH has been replaced with a new one, initialize the power window control system (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION ).
  • Check that the "RR Window Auto Up" and "RR Window Auto Down" power window control system customize settings are "ON" before proceeding with work (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: CUSTOMIZE PARAMETERS ).
  • After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.

HINT:

If the pulse sensor built into the rear power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly RH at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly RH (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: FAIL-SAFE CHART ).

PROCEDURE

1.

READ VALUE USING TECHSTREAM (RR-DOOR MOTOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / RR-Door Motor / Data List.

(e) Read the Data List according to the display on the Techstream.

RR-Door Motor (Rear Power Window Regulator Motor Assembly RH)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

RR Door P/W Auto SW

Rear RH side power window auto switch signal / ON or OFF

ON: Rear RH side power window auto switch operated

OFF: Rear RH side power window auto switch not operated

-

OK:

On the Techstream screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK

2.

PERFORM INITIALIZATION (FOR REAR RH SIDE)

(a) Initialize the rear power window regulator motor assembly RH (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION ).

NEXT

3.

CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)

(a) Check that the rear RH side power window moves when the auto up/down function of the rear power window regulator switch assembly RH is operated (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: OPERATION CHECK ).

OK:

Rear RH side auto up/down function is normal.

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

4.

INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

(a) Remove the rear power window regulator switch assembly RH (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: REAR POWER WINDOW SWITCH: REMOVAL ).

(b) Inspect the rear power window regulator switch assembly RH (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: REAR POWER WINDOW SWITCH: INSPECTION ).

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

OK

5.

CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

(a) Disconnect the I12 rear power window regulator switch assembly RH connector.

(b) Disconnect the I7 rear power window regulator motor assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I12-8 (AUTO) - I7-4 (AUTO)

Always

Below 1 Ω

I12-8 (AUTO) - Body ground

Always

10 kΩ or higher

OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR