Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VK67
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch; 2016 - 2020 MY Sienna [12/2015 -        ]

Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

DESCRIPTION

If the manual up/down function can be performed but the auto up/down function cannot, then the fail-safe mode may be functioning.

If the power window initialization (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION ) has not been performed, the auto up/down function will not operate.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING ).
  • If the front power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION ).
  • Check that the "D Window Auto Up" and "D Window Auto Down" power window control system customize settings are "ON" before proceeding with work (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: CUSTOMIZE PARAMETERS ).
  • After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally

HINT:

If the pulse sensor built into the front power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the multiplex network master switch assembly at the auto up position, and opened manually by pushing down the multiplex network master switch assembly (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: FAIL-SAFE CHART ).

PROCEDURE

1.

READ VALUE USING TECHSTREAM (MASTER SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Master switch / Data List.

(e) Read the Data List according to the display on the Techstream.

Master Switch (Multiplex Network Master Switch Assembly)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto up/down switch signal / ON or OFF

ON: Driver side power window auto switch operated

OFF: Driver side power window auto switch not operated

-

OK:

On the Techstream screen, ON or OFF is displayed accordingly.

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

OK

2.

READ VALUE USING TECHSTREAM (D-DOOR MOTOR)

(a) Enter the following menus: Body Electrical / D-Door Motor / Data List.

(b) Read the Data List according to the display on the Techstream.

D-Door Motor (Front Power Window Regulator Motor Assembly LH)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto up/down switch signal / ON or OFF

ON: Driver side power window auto switch operated

OFF: Driver side power window auto switch not operated

-

OK:

On the Techstream screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 5

OK

3.

PERFORM INITIALIZATION (for Driver Side)

(a) Initialize the front power window regulator motor assembly LH (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION ).

NEXT

4.

CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)

(a) Check that the driver side door power window moves when the auto up/down function of the multiplex network master switch assembly is operated (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: OPERATION CHECK ).

OK:

Driver side auto up/down function is normal.

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

5.

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) Replace the multiplex network master switch assembly (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW MASTER SWITCH: REMOVAL ).

NEXT

6.

CHECK AND REPLACE POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)

(a) Check that the driver side door power window moves when the auto up/down function of the multiplex network master switch assembly is operated (See page 2016 - 2020 MY Sienna [12/2015 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: OPERATION CHECK ).

OK:

Driver side auto up/down function is normal.

OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH