Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VK5Z
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 -           ]
Title: WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: DATA LIST / ACTIVE TEST; 2016 - 2020 MY Sienna [12/2015 -        ]

DATA LIST / ACTIVE TEST

1. READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / (desired system) / Data List / All Data.

(e) Read the Data List according to the display on the Techstream.

Master Switch (Multiplex Network Master Switch Assembly)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto switch signal / ON or OFF

ON: Driver side power window auto switch operated

OFF: Driver side power window auto switch not operated

-

P Door P/W Auto SW

Front passenger side power window auto up/down switch signal / ON or OFF

ON: Front passenger side power window auto switch operated

OFF: Front passenger side power window auto switch not operated

-

RR Door P/W Auto SW

Rear RH side power window auto up/down switch signal / ON or OFF

ON: Rear RH side power window auto switch operated

OFF: Rear RH side power window auto switch not operated

-

RL Door P/W Auto SW

Rear LH side power window auto up/down switch signal / ON or OFF

ON: Rear LH side power window auto switch operated

OFF: Rear LH side power window auto switch not operated

-

P Door P/W Up SW

Front passenger side power window manual up switch signal / ON or OFF

ON: Front passenger side power window manual up switch operated

OFF: Front passenger side power window manual up switch not operated

-

RR Door P/W up switch

Rear RH side power window manual up switch signal / ON or OFF

ON: Rear RH side power window manual up switch operated

OFF: Rear RH side power window manual up switch not operated

-

RL Door P/W up switch

Rear LH side power window manual up switch signal / ON or OFF

ON: Rear LH side power window manual up switch operated

OFF: Rear LH side power window manual up switch not operated

-

P Door P/W Down SW

Front passenger side power window manual down switch signal / ON or OFF

ON: Front passenger side power window manual down switch operated

OFF: Front passenger side power window manual down switch not operated

-

RR Door P/W Down SW

Rear RH side power window manual down switch signal / ON or OFF

ON: Rear RH side power window manual down switch operated

OFF: Rear RH side power window manual down switch not operated

-

RL Door P/W Down SW

Rear LH side power window manual down switch signal / ON or OFF

ON: Rear LH side power window manual down switch operated

OFF: Rear LH side power window manual down switch not operated

-

Door Lock Switch Status

Driver side door control switch lock signal / ON or OFF

ON: Door control switch pushed to lock position

OFF: Door control switch not pushed to lock position

-

Door Unlock Switch Status

Driver side door control switch unlock signal / ON or OFF

ON: Door control switch pushed to unlock position

OFF: Door control switch not pushed to unlock position

-

Window Lock Switch Status

Window lock switch signal / ON or OFF

ON: Window lock switch LOCK position

OFF: Window lock switch UNLOCK position

-

Number of Trouble Codes

Number of trouble codes / Min.: 0 or Max.: 255

Number of DTCs will be displayed

-

D-Door Motor (Front Power Window Regulator Motor Assembly LH)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto switch signal / ON or OFF

ON: Driver side power window auto switch operated

OFF: Driver side power window auto switch not operated

-

D Door P/W Up SW

Driver side power window manual up switch signal / ON or OFF

ON: Driver side power window manual up switch operated

OFF: Driver side power window manual up switch not operated

-

D Door P/W Down SW

Driver side power window manual down switch signal / ON or OFF

ON: Driver side power window manual down switch operated

OFF: Driver side power window manual down switch not operated

-

Glass Position (Close - 1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (1/4 - 2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (2/4 - 3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (3/4 - Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

D Window Auto Up

Auto up operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

D Window Auto Down

Auto down operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

Number of Trouble Codes

Number of trouble codes / Min.: 0 or Max.: 255

Number of DTCs will be displayed

-

P-Door Motor (Front Power Window Regulator Motor Assembly RH)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

P Door P/W Auto SW

Front passenger side power window auto switch signal / ON or OFF

ON: Front passenger side power window auto switch operated

OFF: Front passenger side power window auto switch not operated

-

P Door P/W Up SW

Front passenger side power window manual up switch signal / ON or OFF

ON: Front passenger side power window manual up switch operated

OFF: Front passenger side power window manual up switch not operated

-

P Door P/W Down SW

Front passenger side power window manual down switch signal / ON or OFF

ON: Front passenger side power window manual down switch operated

OFF: Front passenger side power window manual down switch not operated

-

Glass Position (Close - 1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (1/4 - 2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (2/4 - 3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (3/4 - Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

P Window Auto Up

Auto up operation using the front power window regulator switch assembly RH / ON or OFF

Customization status displayed

-

P Window Auto Up From Driver

Remote auto up operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

P Window Auto Down

Auto down operation using the front power window regulator switch assembly RH / ON or OFF

Customization status displayed

-

P Window Auto Down From Driver

Remote auto down operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

Number of Trouble Codes

Number of trouble codes / Min.: 0 or Max.: 255

Number of DTCs will be displayed

-

RL-Door Motor (Rear Power Window Regulator Motor Assembly LH)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

RL Door P/W Auto SW

Rear LH side power window auto switch signal / ON or OFF

ON: Rear LH side power window auto switch operated

OFF: Rear LH side power window auto switch not operated

-

RL Door P/W Up SW

Rear LH side power window manual up switch signal / ON or OFF

ON: Rear LH side power window manual up switch operated

OFF: Rear LH side power window manual up switch not operated

-

RL Door P/W Down SW

Rear LH side power window manual down switch signal / ON or OFF

ON: Rear LH side power window manual down switch operated

OFF: Rear LH side power window manual down switch not operated

-

Glass Position (Close - 1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (1/4 - 2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (2/4 - 3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (3/4 - Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

RL Window Auto Up

Auto up operation using the rear power window regulator switch assembly LH / ON or OFF

Customization status displayed

-

RL Window Auto Up From Driver

Remote auto up operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

RL Window Auto Down

Auto down operation using the rear power window regulator switch assembly LH / ON or OFF

Customization status displayed

-

RL Window Auto Down From Driver

Remote auto down operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

Number of Trouble Codes

Number of trouble codes / Min.: 0 or Max.: 255

Number of DTCs will be displayed

-

RR-Door Motor (Rear Power Window Regulator Motor Assembly RH)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

RR Door P/W Auto SW

Rear RH side power window auto switch signal / ON or OFF

ON: Rear RH side power window auto switch operated

OFF: Rear RH side power window auto switch not operated

-

RR Door P/W Up SW

Rear RH side power window manual up switch signal / ON or OFF

ON: Rear RH side power window manual up switch operated

OFF: Rear RH side power window manual up switch not operated

-

RR Door P/W Down SW

Rear RH side power window manual down switch signal / ON or OFF

ON: Rear RH side power window manual down switch operated

OFF: Rear RH side power window manual down switch not operated

-

Glass Position (Close - 1/4)

Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (1/4 - 2/4)

Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (2/4 - 3/4)

Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

Glass Position (3/4 - Open)

Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution

OK: Normal manual up operation

Caution: Jam detected in the specified range

Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.

RR Window Auto Up

Auto up operation using the rear power window regulator switch assembly RH / ON or OFF

Customization status displayed

-

RR Window Auto Up From Driver

Remote auto up operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

RR Window Auto Down

Auto down operation using the rear power window regulator switch assembly RH / ON or OFF

Customization status displayed

-

RR Window Auto Down From Driver

Remote auto down operation using the multiplex network master switch assembly / ON or OFF

Customization status displayed

-

Number of Trouble Codes

Number of trouble codes / Min.: 0 or Max.: 255

Number of DTCs will be displayed

-

Main Body (Main Body ECU)

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

RR Door Courtesy SW

Rear door courtesy light switch RH signal / ON or OFF

ON: Rear RH side door open

OFF: Rear RH side door closed

-

RL Door Courtesy SW

Rear door courtesy light switch LH signal / ON or OFF

ON: Rear LH side door open

OFF: Rear LH side door closed

-

FR Door Courtesy

Front door courtesy light switch RH signal / ON or OFF

ON: Front passenger side door closed

OFF: Front passenger side door open

-

FL Door Courtesy

Front door courtesy light switch LH signal / ON or OFF

ON: Driver side door closed

OFF: Driver side door open

-

Communication D-Door Motor

Connection status between front power window regulator motor assembly LH and main body ECU / OK or STOP

OK: Normal communication

STOP: Communication stopped

-

Communication P-Door Motor

Connection status between front power window regulator motor assembly RH and main body ECU / OK or STOP

OK: Normal communication

STOP: Communication stopped

-

Communication RR-Door Motor

Connection status between rear power window regulator motor assembly RH and main body ECU / OK or STOP

OK: Normal communication

STOP: Communication stopped

-

Communication RL-Door Motor

Connection status between rear power window regulator motor assembly LH and main body ECU / OK or STOP

OK: Normal communication

STOP: Communication stopped

-

Communication Master SW

Connection status between multiplex network master switch and main body ECU / OK or STOP

OK: Normal communication

STOP: Communication stopped

-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / (desired system) / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

D-Door Motor (Front Power Window Regulator Motor Assembly LH)

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Power window

OFF / UP /DOWN

-

P-Door Motor (Front Power Window Regulator Motor Assembly RH)

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Power window

OFF / UP /DOWN

-

RL-Door Motor (Rear Power Window Regulator Motor Assembly LH)

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Power window

OFF / UP /DOWN

-

RR-Door Motor (Rear Power Window Regulator Motor Assembly RH)

Tester Display

Test Part

Control Range

Diagnostic Note

Power Window

Power window

OFF / UP /DOWN

-

Main Body (Main Body ECU)

Tester Display

Test Part

Control Range

Diagnostic Note

IG OFF P/W Control Permission Output

Power window

OFF / ON

Perform this Active Test with the ignition switch off