| Last Modified: 08-28-2024 | 6.11:8.1.0 | Doc ID: RM100000000VK5R |
| Model Year Start: 2016 | Model: Sienna | Prod Date Range: [12/2015 - ] |
| Title: WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: Rear Power Window RH does not Operate with Rear Power Window Switch RH; 2016 - 2020 MY Sienna [12/2015 - ] | ||
|
Rear Power Window RH does not Operate with Rear Power Window Switch RH |
DESCRIPTION
When the engine is running or the ignition switch is ON, the rear power window regulator motor assembly RH is operated by the rear power window regulator switch assembly RH. The rear power window regulator motor assembly RH has motor, regulator, and ECU functions.
HINT:
If the pulse sensor built into the rear power window regulator motor RH malfunctions, the power window control system enters fail-safe mode. The remote up/down and auto up/down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly RH at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly RH.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page
![2016 - 2020 MY Sienna [12/2015 - ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
).
-
If the rear power window regulator motor assembly RH has been replaced with a new one, initialize the power window control system (See page
).
- Check that the window lock switch is off before performing the following procedure.
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (MAIN BODY) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Main Body (Main Body ECU)
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Communication RR-Door Motor |
Connection status between rear power window regulator motor assembly RH and main body ECU / OK or STOP |
OK: Normal communication STOP: Communication stopped |
- |
OK:
On the Techstream screen, OK is displayed.
| NG |
|
GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) |
|
|
2. |
READ VALUE USING TECHSTREAM (RR-DOOR MOTOR) |
(a) Enter the following menus: Body Electrical / RR-Door Motor / Data List.
(b) Read the Data List according to the display on the Techstream.
RR-Door Motor (Rear Power Window Regulator Motor Assembly RH)
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
RR Door P/W Up SW |
Rear RH side power window manual up switch signal / ON or OFF |
ON: Rear RH side power window manual up switch operated OFF: Rear RH side power window manual up switch not operated |
- |
|
RR Door P/W Down SW |
Rear RH side power window manual down switch signal / ON or OFF |
ON: Rear RH side power window manual down switch operated OFF: Rear RH side power window manual down switch not operated |
- |
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
| NG |
|
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM (RR-DOOR MOTOR) |
(a) Enter the following menus: Body Electrical / RR-Door Motor / Active Test.
(b) Perform the Active Test according to the display on the Techstream.
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
RR-Door Motor (Rear Power Window Regulator Motor Assembly RH)
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Power window |
OFF / UP / DOWN |
- |
HINT:
Up and down movement does not occur if the arrow is not pressed and held.
OK:
Rear RH side power window operates normally.
| OK |
|
| NG |
|
|
4. |
INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
(a) Remove the rear power window regulator switch assembly RH (See page
).
(b) Inspect the rear power window regulator switch assembly RH (See page
).
| NG |
|
|
|
5. |
CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
(a) Disconnect the I12 rear power window regulator switch assembly RH connector.
(b) Disconnect the I7 rear power window regulator motor assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I12-5 (UP) - I7-10 (UP) |
Always |
Below 1 Ω |
|
I12-4 (DOWN) - I7-7 (DOWN) |
Always |
Below 1 Ω |
|
I12-7 (GND) - Body ground |
Always |
Below 1 Ω |
|
I12-5 (UP) - Body ground |
Always |
10 kΩ or higher |
|
I12-4 (DOWN) - Body ground |
Always |
10 kΩ or higher |
|
I7-10 (UP) - Body ground |
Always |
10 kΩ or higher |
|
I7-7 (DOWN) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|