Last Modified: 04-05-2023 6.11:8.1.0 Doc ID: RM100000000VK4U
Model Year Start: 2016 Model: Sienna Prod Date Range: [12/2015 - 11/2017]
Title: INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL; 2016 - 2017 MY Sienna [12/2015 - 11/2017]

REMOVAL

PROCEDURE

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page 2016 MY Sienna [12/2015 - 08/2016]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2017 MY Sienna [08/2016 - 11/2017]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION ).

2. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)

(See page 2016 - 2020 MY Sienna [12/2015 -        ]; AUDIO / VIDEO: TELEVISION DISPLAY: REMOVAL )

3. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

(a) Disengage the 12 claws to remove the door scuff plate assembly RH.

4. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.

5. REMOVE COWL SIDE TRIM BOARD RH

(a) Remove the clip.

(b) Disengage the claw and clip to remove the cowl side trim board RH.

6. REMOVE COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side.

7. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

9. REMOVE FRONT PILLAR GARNISH RH

(a) Separate the front pillar garnish clip from the front pillar garnish RH.

Text in Illustration

*1

Front Pillar Garnish Clip

(b) Disengage the clip.

(c) Press the 2 areas indicated by the arrows in the illustration.

(d) Disengage the front pillar garnish clip and 3 guides to remove the front pillar garnish RH.

(e) Remove the front pillar garnish clip from the front pillar garnish RH.

(f) Protect the curtain shield airbag assembly.

Text in Illustration

*1

Adhesive Tape

*2

Protective Cover

(1) Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape, as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

10. REMOVE FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.

11. REMOVE FRONT PILLAR LOWER GARNISH RH

(a) Disengage the 2 claws to remove the front pillar lower garnish RH.

12. REMOVE FRONT PILLAR LOWER GARNISH LH

HINT:

Use the same procedure as for the RH side.

13. REMOVE REAR DOOR SCUFF PLATE RH

(a) Disengage the 4 claws, 7 clips and guide to remove the rear door scuff plate RH.

14. REMOVE REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.

15. SEPARATE SLIDE DOOR WEATHERSTRIP RH

16. SEPARATE SLIDE DOOR WEATHERSTRIP LH

17. REMOVE BACK DOOR SCUFF PLATE

(a) Disengage the 2 claws to open the flap.

(b) Remove the bolt.

(c) Disengage the 2 claws to remove the hook cover assembly.

HINT:

Use the same procedure for the other 2 hook covers.

(d) Disengage the 6 clips and 2 guides to remove the back door scuff plate.

18. SEPARATE BACK DOOR WEATHERSTRIP

19. REMOVE ROOF HEADLINING REAR GARNISH

(a) Disengage the 2 claws and the 6 clips to remove the roof headlining rear garnish.

20. REMOVE CENTER PILLAR LOWER GARNISH RH

(a) Disengage the 3 claws to remove the anchor cover.

(b) Remove the bolt to separate the front seat outer belt RH on the floor anchor side.

(c) Disengage the 4 claws and 2 clips to remove the center pillar lower garnish RH.

21. REMOVE CENTER PILLAR LOWER GARNISH LH

HINT:

Use the same procedure as for the RH side.

22. REMOVE CENTER PILLAR UPPER GARNISH RH

(a) Using a moulding remover, disengage the 4 claws to remove the power slide door control switch (w/ power slide door).

(b) Disconnect the connector (w/ power slide door).

(c) Remove the screw.

(d) Disengage the 2 clips to remove the center pillar upper garnish RH.

23. REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:

Use the same procedure as for the RH side.

24. SEPARATE REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

(a) Disengage the 3 claws to remove the anchor cover.

(b) Remove the bolt to disconnect the rear No. 2 seat outer belt RH on the floor anchor side.

(c) Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws to open the anchor cover.

(d) Loosen the bolt and shoulder anchor.

25. SEPARATE REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.

26. REMOVE QUARTER TRIM PANEL ASSEMBLY RH

(a) Disengage the 9 claws and 8 clips.

(b) Disconnect the connectors to remove the quarter trim panel assembly RH.

27. REMOVE QUARTER TRIM PANEL ASSEMBLY LH

(a) Disengage the 11 claws and 8 clips.

(b) Disconnect the connectors to remove the quarter trim panel assembly LH.

28. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH

(a) Disengage the 8 claws to remove the belt hole cover.

(b) Depress the center portion of the trim hook, disengage the 2 claws to remove the trim hook.

(c) Disengage the 5 clips.

(d) Disconnect the connectors to remove the rear No. 2 window side garnish assembly RH.

29. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH

(a) Depress the center portion of the trim hook, disengage the 2 claws to remove the trim hook.

(b) Disengage the 5 clips and guide to remove the rear No. 2 window side garnish assembly LH.

30. REMOVE QUARTER LOCK PILLAR GARNISH RH

(a) Disengage the 2 claws to remove the anchor cover (w/ rear No. 1 seat belt).

(b) Remove the bolt to separate the rear No. 1 seat outer belt (w/ rear No. 1 seat belt).

(c) Disengage the 3 claws to open the cover.

(d) Remove the bolt.

(e) Disengage the 4 clips to remove the quarter lock pillar garnish.

31. REMOVE QUARTER LOCK PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.

32. REMOVE ASSIST GRIP SUB-ASSEMBLY

(a) Disengage the 4 claws to remove the 2 assist grip covers.

(b) Disengage the 2 clips to remove the assist grip sub-assembly.

(c) Remove the 2 clips from the vehicle body.

HINT:

Use the same procedure for the other assist grip.

33. REMOVE REAR ASSIST GRIP ASSEMBLY

(a) Disengage the 4 claws to remove the 2 assist grip covers.

(b) Disengage the 2 clips to remove the rear assist grip assembly.

(c) Remove the 2 clips from the vehicle body.

HINT:

Use the same procedure for the other 3 rear assist grips.

34. REMOVE VISOR ASSEMBLY RH

2016 - 2020 MY Sienna [12/2015 -        ]; LIGHTING (INT): VANITY LIGHT: REMOVAL+

35. REMOVE VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.

36. REMOVE VISOR HOLDER

(a) Remove the screw and visor holder.

37. REMOVE ROOF CONSOLE BOX ASSEMBLY

2016 - 2020 MY Sienna [12/2015 -        ]; SLIDING ROOF / CONVERTIBLE: SLIDING ROOF SWITCH ASSEMBLY: REMOVAL+

38. REMOVE NO. 6 REAR AIR DUCT

(a) Remove the 2 bolts and outer belt anchor bracket.

(b) Disengage the 2 claws to remove the cooler plate.

(c) Remove the No. 6 rear air duct.

39. REMOVE ROOF HEADLINING ASSEMBLY

(a) Disconnect the connectors.

(b) Disconnect the 2 washer hoses.

(c) Using a clip remover, remove the 3 clips to roof headlining assembly.

(d) Using a clip remover, remove the clip to roof headlining assembly (w/ rear sliding roof).

(e) Remove the roof headlining assembly from the vehicle through the back door.

NOTICE:

Do not damage the roof headlining assembly or body interior.